Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Graphtec CE8000 and CE7000 print and cut: registration marks not reading or cuts off the print
Load print and cut jobs as ROLL-1 or SHEET, never ROLL-2. Print black marks on a white background, 0.3 to 1.0 mm thick and 5 to 20 mm long, with nothing else printed near them. If the marks still aren't read, try a different file, then run Graphtec's ARMS test. If marks are read but cuts land off the print, check the plunger position and the sensor offset, then the connection and software.
Match your symptom
| Symptom | Start at |
|---|---|
| Marks not read, or E04 errors | Steps 1 to 4 |
| Marks read, cuts shifted the same way every time | Steps 5 and 6 |
| Marks read, cuts off by different amounts | Step 7 |
Marks the cutter can read
- Use one of Graphtec's four mark types. Types 3 and 4 should be made in Adobe Illustrator.
- Single lines 0.3 to 1.0 mm thick, mark size 5 to 20 mm. Double lines don't work.
- Black on white reads best. Keep the area right around each mark free of other printing; Graphtec's diagrams show a 6 mm scan zone.
- Keep the marks away from the media edge and make sure the push rollers sit outside the marks.
- Turn Panel Cutting off. With it on, ARMS is not available.
- Store media in the same room conditions as the cutter. Graphtec notes media can stretch or shrink as soon as it comes off the roll, which shifts the print against the marks.
Step by step
-
Load as ROLL-1 or SHEET
When you raise the media set lever, choose ROLL-1 FRONT EDGE for roll media or SHEET for sheets. Graphtec says never to use ROLL-2 for print and cut.
-
Try a different file
Graphtec's first check, even if the same file cut fine before. If a fresh file reads, the problem is in the file or the software.
-
Run the ARMS sensor test
Print Graphtec's standard mark pattern on a desktop printer and load it. Open the menu, then ARMS > SENSOR ADJUSTMENT > TEST ARMS SENSOR, pick the mark type, move the carriage into the starting area and press ENTER. The cutter finds the marks and cuts a cross, so mind the blade. If every mark reads, the cutter is fine; go to step 7.
-
Adjust the sensor level
For media that isn't plain white, use ARMS > SENSOR ADJUSTMENT > SENSOR ADJUST > SCAN on a printed mark so the cutter sets its own level. If that fails, set SENSING LEVEL by hand (X and Y, 30 to 90). Raise it when the mark color is close to the media color; lower it when the sensor reads folds or dirt as marks. On colored or glossy media, also turn automatic mark detection off.
If the ARMS test still fails, Graphtec's guide resets the cutter to factory settings next. That erases your cut conditions, so write them down first, or text us and we'll go through it with you.
-
Check the tool position
If cuts are about a quarter inch off sideways, check that the plunger is in the correct holder position and that ASSIGN TOOL in the cut condition matches it (1 for rear, 3 for front).
-
Check the sensor offset
The sensor sits a set distance from the blade tip, and the cutter corrects for it. If the cut shift is the same size and direction every time, Graphtec's sensor offset check ("Adjust for the registration mark scan position" in chapter 5 of the manual) confirms and corrects it. Also make sure the media was loaded straight with the push rollers set correctly.
-
Check the connection and software
If the shift varies from job to job, test the connection: USB cable under 15 feet, no hubs or adapters, or switch from network to USB. Then cut the same job from Graphtec's software. If that works, contact the maker of your other software. If cuts are only off on specialty media, make sure the cutter's firmware is current.
ARMS error codes
| Code | Meaning | What to do |
|---|---|---|
| E04001 | Media tilted too much | Reload the media straight |
| E04005 | Could not scan the marks | Check the scan start position |
| E04008 | Media end found while scanning | Check the media and where the marks are printed |
| E04009 to E04017 | Scan went past the detection area | Check the media and the mark print position |
| E04018 | Media set lever lowered | Reload and try again |
| E04021 to E04025 | Marks not detected | Check mark color, media and print position |
Need a hand?
Record a short video of the cutter scanning the marks and text it, with a photo of the cut result, to (562) 609-4996.
Watch Graphtec's video: the ARMS test
More videos
Embedded from the manufacturer's official channel.
Common questions
How accurate is print and cut on the CE8000?
Graphtec states that the sensor reads its specified registration marks to within 0.3 mm.
Can it read marks on colored or glossy media?
Sometimes. Graphtec tunes the sensor for black on white. For colored or glossy media, turn automatic mark detection off, adjust the sensor level, and move the carriage to the first mark yourself.
The marks read but every cut is about a quarter inch off sideways.
Graphtec's guide says to check that the plunger sits in the correct tool position and that ASSIGN TOOL in the cut condition matches it.
Why does it say it can't find the marks on laminated prints?
Graphtec lists laminated media, depending on the laminate, as hard to read. So are transparent, folded, dirty or blurred prints.
Where do I get the ARMS test sheet?
Graphtec America posts it on its FAQ page, and the manual names the test pattern files ARMStest_type1 and ARMStest_type2.
- Graphtec CE8000 Series User's Manual
- Graphtec: Print and Cut Issues and Solutions for the CE7000 Series
- Graphtec ARMS Test Sheet
- Graphtec America self-help FAQ
- AA support requests about Graphtec print and cut, 2024 to 2026











































































