Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
How to update Graphtec CE8000 firmware with a USB flash drive, then reset to factory settings
Download the CE8000 firmware from Graphtec America, put that single .x file on a FAT32 USB flash drive, unplug the USB cable, insert the drive with the cutter off, then switch on while holding LEFT and RIGHT. Press ENTER at "Press ENTER key to start update" and don't touch anything until it reinitializes. Graphtec then recommends a factory reset (hold UP within 2 seconds of power on, SET DEFAULT, YES).
Before you start
- Check your current version. It shows on the display when the cutter powers on. You can also open the menu and press INFO, which shows the firmware version and serial number.
- Download the right file. Get the CE8000 firmware from the downloads section of Graphtec America's CE8000 page. The firmware file ends in .x.
- Write down your cut conditions. Graphtec recommends a factory reset after updating, which clears your saved settings.
- Make sure power won't drop. A power cut during the update is the one thing to avoid.
Do not turn the cutter off or pull the USB flash drive until the update has finished.
Step by step
-
Prepare the flash drive
Format a USB flash drive as FAT32. Delete everything on it, then copy on only the one CE8000 firmware file (.x). Graphtec wants it to be the only file on the drive.
-
Disconnect the computer
Unplug the USB cable so the cutter is not connected to a computer.
-
Insert the drive
With the cutter switched off, put the flash drive in the cutter's USB flash drive port.
-
Power on holding LEFT and RIGHT
Switch the cutter on while holding both the LEFT and RIGHT keys on the control panel.
-
Start the update
When Press ENTER key to start update appears, let go of the arrow keys and press ENTER.
-
Wait
Progress shows on the control panel. Leave it alone until it finishes. The cutter initializes by itself afterward.
-
Confirm the version
Watch the screen during initialization and check that it shows the new firmware version.
-
Reset to factory settings
Graphtec recommends this after a CE8000 update. Turn the cutter off, turn it back on, and within 2 seconds press and hold the UP arrow key. On the touch screen select SET DEFAULT, then YES. When SET DEFAULT COMPLETE appears, turn the cutter off and on again and follow the screen to set the language and units.
-
Put your settings back
Re-enter the cut conditions you wrote down, remove the flash drive, and run a cut test before your next job.
Why update
Graphtec's CE8000 release notes list fixes for problems shops actually run into, for example:
- Some USB flash drives not being recognized
- Keys that could stop working if the set lever was lowered while registration marks were being read
- The origin or home position becoming wrong after changing the EXPAND setting with the set lever lowered
- The second job not being cut when several jobs were sent on sheet media
- Several fixes for the ASF sheet feeder and wireless LAN
Newer versions also add features, such as Y SEGMENT registration marks. Read the release notes for the version you download.
Other ways to update
Graphtec's CE8000 brochure says you can check for and download new firmware through Graphtec Studio 2 or Cutting Master 5, and install it by flash drive or over the USB cable. Graphtec's Cutting Master 5 video on this page shows the software route. The USB flash drive method above is the one Graphtec documents step by step.
If it doesn't work
Check that the cutter was off when you inserted the drive, that you held LEFT and RIGHT (not UP) while switching on, and that the drive is FAT32 with only the .x file on it. This procedure is for the CE8000. If you have a CE7000, or the cutter doesn't come back after an update, text us at (562) 609-4996 before trying again.
Watch Graphtec's video: firmware update from Cutting Master 5
Embedded from the manufacturer's official channel.
Common questions
How do I find my firmware version?
It shows on the display at power on, and under INFO in the menu along with the serial number.
The cutter doesn't see my flash drive.
Format it as FAT32, delete everything on it, and leave only the one .x firmware file. Try another drive if it still isn't recognized; some drives weren't recognized on older firmware.
Do I have to reset to factory settings?
Graphtec recommends it after a CE8000 firmware update. It clears your saved settings, so write down your cut conditions first.
Can I update without a flash drive?
Graphtec says you can check for and download firmware in Graphtec Studio 2 or Cutting Master 5 and install it over the USB cable. The flash drive method is the one Graphtec documents step by step.
Does this work on a CE7000?
This procedure is Graphtec's CE8000 document. Contact us before updating a CE7000.











































































