Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Seismo V36R setup and settings: alignment, modes, temperatures and powder return
Keep about 200 to 300 mm (8 to 12 in) between the printer and the V36R, with the film centered and lying flat against the front heating plate. Spread about 0.25 kg of powder on the film by hand to start, then fill the powder box (3 kg maximum). DTF Station's starting settings are belt 30, shaker 15, powder return 15, front dryer 130°C, rear dryer 120°C and front guide plate 60°C, tuned to your powder and film.
The V36R is controlled from its touch screen. Tap any value to change it, enter the number and confirm. Before the first run, make sure the cooling fan and take-up are installed, the ground wire is connected and the machine is on a 220 V supply.
Line it up with the printer
-
Gap
Leave about 200 to 300 mm (8 to 12 in) between the front heating plate of the shaker and the front heating plate of the printer. This keeps the film from wandering on its way to the take-up.
-
Center the film
The film should run down the middle of the machine. Film that hangs past the edge of the front heating plate doesn't get heated there and causes defects.
-
Keep it flat on the plate
The film should lie flat and tangent to the front heating plate. If it lifts off the plate, part of it won't be preheated.
Load powder
For the first run, spread about 0.25 kg of powder evenly over the film by hand. Then open the powder box cover and add powder, up to 3 kg. Keep the bag or scoop as low as you can while pouring so less powder goes into the air.
Choose a mode
| Mode | What happens |
|---|---|
| Automatic | Runs only while the sensor sees film. Use this for normal production. |
| Manual | Runs continuously and ignores the sensors. Use it to finish the end of a roll. |
| Stop | Stops powder, shaking and the belt. Heat and other functions keep running. |
Starting settings
| Setting | DTF Station starting value |
|---|---|
| Belt speed | Level 30 |
| Shaker speed | Level 15 |
| Powder return | Level 15 |
| Front (upper) dryer | 130°C (266°F) |
| Rear (lower) dryer | 120°C (248°F) |
| Front guide plate | 60°C (140°F) |
These are reference values. Adjust temperatures to your powder's melting point and your film. Check the cured film: it should lie flat with no obvious wrinkles, and the edges should line up from the feed side to the take-up. Turn each heater on or off with its power icon: red is off, green is on. The front and rear belt vacuum can run together or separately.
Powder controls
- Manual Dispense: drops powder once.
- Manual Powder Return: runs the return for 40 seconds. Tap again to stop it early.
- Powder Box Cleaning: hold for 3 seconds. The outlet opens wider and vibrates hard to clear old powder, so put a container underneath first.
Settings menu and shutdown
Hold the settings key for 3 seconds to change the automatic powder removal delay, maximum belt speed, maximum shaking speed and language. When curing is finished, turn off all the heating switches, then follow the V36R end-of-day cleaning.
The V36R has a built-in fire protection mode that engages if it detects a fire hazard. If it triggers, or the machine won't heat, won't move the belt, or shows a message you don't recognize, power it down and Text us a photo or short video at (562) 609-4996.
Common questions
Why does the belt stop when there's no film?
In Automatic mode the V36R only runs when its sensor sees film. With no film the belt stops at once, and powder and shaking stop 10 seconds later. It restarts by itself when film arrives.
Why did the temperature drop 20 degrees by itself?
That is Auto Standby Heating. In Automatic mode, if printing stops for 20 seconds the dryers drop 20°C below the set point and return when printing resumes. It does not run in Manual or Stop mode.
The roll is almost finished and the machine stopped. What do I do?
Switch to Manual mode, which ignores the sensor, to run the last of the film through.
What does the powder return level do?
It sets how much powder is returned, from 1 to 30. The default of 15 suits most print speeds. Higher means more powder.
What is engineering mode in the settings?
It is for technicians and is not accessible to users. Don't try to enter it. Factory reset is also in that menu.
- Seismo V36R user manual
- Seismo V36R product manual
- Seismo V36R product specifications
- DTF Station technical documentation
- Seismo V36R assembly and stand guide (DTF Station)











































































