Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPD-924D daily and weekly maintenance: white shake, CR Maintenance, capping station, wiper and spit pad
Every day before you wake the XPD-924D, shake both white cartridges for 2 to 3 minutes, run CR Maintenance from Menu 11 and clean the capping station, wiper and spit pad with dry cleaning sticks, then print a nozzle check. Once a week, deep clean those parts and the area around the print heads. Keep the printer on in Sleep Mode overnight with auto cleaning every 4 to 6 hours.
Every day, before you wake the printer
-
Shake both white cartridges
Pull out the two white cartridges. Hold each one flat and shake it side to side with the slot guide facing up, then again with it facing down, for 2 to 3 minutes in total, or as long as the printer's main screen tells you. STS also suggests turning it upside down so everything mixes. STS sells a cartridge shaker that does this at 150 rpm for 4 minutes. Color cartridges only need shaking when new or when the printer asks.
-
Wake the printer
Slide the cartridges back into their own slots and tap Enter to leave Sleep Mode.
-
Open CR Maintenance
Tap Home, step to Menu 11 CR Maintenance and tap Enter at Start -> Enter. The carriage moves to the left and the cleaning wiper rises. Open the front cover and the right maintenance cover.
-
Clean the capping station, wiper and spit pad
With a dry cleaning stick, wipe both sides of the cleaning wiper back and forth. Clean both the color wiper and the white wiper. Then clean the grey rubber rim around both caps. Do not touch the yellow absorber inside the caps. Clean the spit pad. Leave no ink and no moisture behind. If a stain will not come off, close up, run a Short cleaning and try again.
-
Close up
Close the maintenance cover and front cover, tap Enter at CR Maintenance End -> Enter, then tap Home.
-
Check the platen and media guards
The heated metal platen the film runs over should be free of ink and residue. Clean the media guards (edge holders) and the area under them.
-
Print a nozzle check
Load film and print a nozzle check from the panel (STS calls it nozzle check B). If lines are missing, run a Short cleaning and check again until the pattern is complete. If that doesn't clear it, follow our clogged nozzle guide instead of cleaning over and over.
-
Look at the waste ink tank
Empty it when it is more than half full or the panel shows Full WasteInkTank. It holds 2,000 ml, so use a container at least that big. Put paper on the floor, open the waste ink valve, drain, close the valve securely and wipe it. Waste ink is industrial waste: dispose of it under your local rules.
Use each cleaning stick dry, once, and never touch its tip. Finish each area in about 5 minutes. A damp, reused or dried-out stick can damage the print head. Never touch the metal nozzle plate under the carriage.
Every week: deep clean
-
Clean the wiper and caps thoroughly
In CR Maintenance, remove the parts you can reach and clean every surface, including the underside of the wiper and the base around it. Clear the drain paths and tubes under the wiper and spit pad.
-
Rinse with cleaning solution
Pour a little STS Cleaning Solution into the spitting box and the wiper assembly. Do not use Nozzle Busting solution for this. Use a swab to lift any hardened DTF ink.
-
Clean around the print head
Open the left maintenance cover. With a fresh dry stick, clean ink and dust from the space between each head and its guide, the sides of the heads, and the black plastic head guides and ramps at each end. Do not touch the head surface.
After 10 minutes in CR Maintenance with covers open, the printer beeps and shows "Close cover". Close all covers, tap Enter to exit, and start CR Maintenance again.
Longer intervals
| When | What to do |
|---|---|
| Monthly | Inside cleaning: power off and unplug, let the platen cool, brush dust off the pressure rollers with a soft brush (never a gas duster), and wipe ink off the platen, media guide and edge holders with a cloth lightly dampened with ethanol of 50% or stronger |
| About every 2 months | Check the flushing box absorber behind the right cover. Replace it when lumps of ink rise above its frame |
| Every 3 to 4 months | Long Store to flush sediment from the ink lines (see our Long Store guide) |
| Every 12 months | Replace the cleaning wiper. Use the black wiper for head heights Low1, Low2 and Middle, the grey one for High |
| As needed | STS lists greasing the carriage rails and wiping the encoder strip with DI water. Text us before your first time, because STS warns that opening outer covers without their direction voids the warranty |
Overnight settings
Keep the 924D powered on in Sleep Mode every night so it can circulate ink and clean itself. Under Menu 6 Sleep Mode > Sleep Mode 1 Cleaning Setting, STS recommends a cleaning every 6 hours, or every 4 hours or less in a hot or dry room. Sleep cleanings are skipped if a cover is open, the pressure rollers are released, the waste tank is full or a cartridge or S/C card is out, so close everything up before you leave.
Text us a photo or short video at (562) 609-4996 if a part looks damaged or the nozzle check won't come clean.
Watch STS: CR Maintenance on the XPD-924D, step by step
More videos
Embedded from the manufacturer's official channel.
Common questions
Can I turn the 924D off at night?
STS says no. Leave it on in Sleep Mode so it can circulate ink and run scheduled cleanings. Put it on a surge protector; STS recommends at least a 500VA UPS.
Do I need to shake the color cartridges too?
Only when they are new or when the printer asks. The white settles quickly because of its titanium dioxide pigment, so it gets shaken every day.
Can I use Nozzle Busting solution to clean the wiper?
No. STS says to use STS Cleaning Solution in the spitting box and wiper assembly. Nozzle Busting solution is for soaking after a head strike.
How do I know the flushing box absorber needs changing?
Open the right maintenance cover and look at it. When lumps of ink rise above the frame, replace it. That is roughly every two months, depending on how much you print.
What if I can only print a little this month?
STS asks for at least one full set of 500 ml cartridges a month, or at minimum its STS Inks Test Print (22.5 x 16 inches) three times a week. A nozzle check alone uses too little ink to keep the lines healthy.
- STS Maintenance Procedures, Recommended Usage and Environmental Guidelines (XPD2 / 924D)
- STS XPD-924D Operation Manual (v5)
- STS/Mutoh 924D XPD2 Printer Guidelines
- STS XPD-924D Recommended Usage and Warranty Bulletin
- AA support requests about the STS XPD-924D, 2024 to 2026











































































