Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPJ-1682D calibration: white layer not lining up, banding and white lines (Adjust Print, Adjust Head, PF Adjust)
If the white layer on an XPJ-1682D print doesn't line up with the color, or prints look banded with a clean nozzle check, calibrate from the panel. Run Adjust Print first (Menu 1 Setup, your user type, Adjust Print, Auto). If that isn't enough, run head alignment (Menu 2 Test Print 5 Adjust Head) and then Adjust Print again. Thin white lines across the print call for the media feed adjustment (PF Adjust 6 Auto).
The XPJ-1682D has two print heads and a built in color sensor. When the nozzle check is perfect but prints still look wrong, Mutoh gives owners three panel calibrations. AA tickets for this printer often describe the white layer not lining up with the color, which leaves white lines along the edges. That is what head alignment and print quality calibration are for.
Match your symptom
| Symptom | What to run |
|---|---|
| Grainy or banded | Print quality calibration (Adjust Print) |
| Layers offset | White and color don't line up: head alignment (Adjust Head), then Adjust Print |
| White lines | Thin white lines or overlapping bands across the print: media feed adjustment (PF Adjust) |
| Setup changed | Head height changed: Adjust Print. New film or roller pressure changed: PF Adjust |
Print a nozzle check and clean until it is complete before you calibrate. Load the film straight and let the heater warm up (answer No to Skip Heater Warm Up?). Don't touch the media guide during Warming Up. Adjust Print and Adjust Head need at least 550 mm of printable width, and PF Adjust needs 400 mm.
Print quality calibration (Adjust Print)
-
Open the menu
Tap Home, go to Menu 1 Setup > Setup 1 User Type, pick the user type you print with, and step to Type ** : 2 Adjust Print. Enter the film thickness (default 170 µm).
-
Auto
Choose Adjust Print 3: Auto, then Standard (the user type's print mode) or ALL (patterns A to C). The printer prints, reads the pattern with the color sensor, and shows Auto Adjust Succeeded or Failed.
-
Manual
Adjust Print 1: Standard adjusts only the user type's print mode, so your RIP must match its resolution, passes and direction. Adjust Print 2: Custom covers patterns A to C. Print the Confirm Pattern, then the Rough Pattern: for head 1 enter the best aligned block (1 to 21), then head 2. Repeat with the Fine Pattern (1 to 7), checking the sides and center.
On the 1682D, Quality 3 and 4 and Graphics 1 and 2 use pattern B, and the Banner modes use pattern A.
Head alignment (Adjust Head)
-
When
If Adjust Print doesn't fix it, if unidirectional prints look poor, or after switching to thin film.
-
Run it
Go to Menu 2 Test Print > Test Print 5 Adjust Head. Choose Adjust Head 1: Standard (the user type's mode) or Adjust Head 2: Custom (Fine Pattern ALL or A to C). Find the block with the fewest white lines or overlaps, numbered 1 to 7, and enter it.
-
Then Adjust Print again
Head alignment can upset bidirectional placement, so Mutoh says to run Adjust Print afterward.
Media feed adjustment (PF Adjust)
-
Auto
In the user type, go to Type ** : 3 PF Adjust and choose PF Adjust 6: Auto. Note that the numbering differs from the 924D: Auto is number 6 on the 1682D.
-
Manual
Choose PF Adjust 1: Initial Print (250 mm feed by default; a longer feed is more accurate). Cut it off, measure between the marks with a ruler, and enter the measurement in PF Adjust 2: Initial Change. Check it with PF Adjust 3: Confirm Print. Once the measurement matches, print PF Adjust 4: Micro Print and enter the value under the cleanest block. If you already know the value for a film, enter it in PF Adjust 5: Micro Change.
-
During a job
Menu 5 PF Micro Adjust tweaks feed for the current job (-5 to +5%). Save it with Menu 6 Backup.
When to recalibrate
- After changing the head height lever (Low, Mid, High): Adjust Print.
- After changing the media feed lever or any roller slide lock: PF Adjust.
- For a new film type, or after moving the printer: PF Adjust and Adjust Print.
Text us a photo or short video at (562) 609-4996 if the layers still don't line up after Adjust Head and Adjust Print. Physical head adjustment is technician work.
Common questions
My white layer is offset from the color. Which calibration fixes that?
Run Adjust Print first. If it is still offset, run Test Print 5 Adjust Head, then Adjust Print again.
Where is Auto in PF Adjust?
On the 1682D it is PF Adjust 6: Auto. PF Adjust 1 to 5 are the manual ruler method.
The calibration won't print and says Outside Print Area. Why?
The patterns need at least 550 mm (Adjust Print, Adjust Head) or 400 mm (PF Adjust) of printable width. Check the side margin, origin and loaded film width.
Will calibration fix missing nozzles?
No. Clean until the nozzle check is complete first. Calibration only moves where the drops land.
Are the values kept when I change user type?
They are saved per user type. Calibrate the user type you actually print with, or copy it with Copy User Type.
- STS XPJ-1682D Operation Manual
- AA support requests about the STS XPJ-1682D, 2024 to 2026











































































