Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPJ-1682D error messages and troubleshooting: panel messages, E-code restarts, stubborn clogs and color problems
Most XPJ-1682D messages are fixed at the printer: close covers, lower the media lever, reseat an ink pack adapter, agitate the white, or empty the waste tank. If all lights blink with an E code, clear any obstruction and restart, and contact us with the code if it returns. For nozzles that won't recover, go Normal or Long, then Little Charge, then clean the wiper and caps in CR Maintenance before calling us.
Start in MSM: Printer Status > Status Information shows the current error. Keep MSM current with Help > Version > Check for updates. For S/C card errors use our S/C card guide; if MSM or the RIP can't find the printer, use our MSM connection guide.
Panel messages
| Message | What to do |
|---|---|
| Cover Open | Close the front cover and both maintenance covers |
| Put Lever Back | Lower the media feed lever |
| Hold Media, Undefined Media, Media Slant | Reload the film straight. Use new film |
| Change Head Gap *** | The printer's head height (High, Mid or Low) doesn't match the job. Make them match |
| [slot] No Cart. | Insert that slot's ink pack adapter all the way |
| [slot] Check Ink | The adapter isn't detected. Pull it and push it back in. If it persists, contact us |
| [slot] Ink Low, Ink End | Get a new bag ready, then replace bag and S/C card |
| [slot] Change Plug | Replace that adapter's plug (see our ink bag guide) |
| Shake W Cartridge | Agitate the white bags. After 12 hours of ignoring it, the printer stops printing |
| Nozzle Check F Start -> Enter | A week in Sleep Mode. Tap Enter, agitate the ink, print a nozzle check |
| Full WasteInkTank | Empty the waste tank now |
| [slot] Discharged | Run Initial Charge |
| Life Times [pump, motor, C Pump] | A part is near end of life. Keep printing and contact us |
| E***Err, all lights blinking | An error that needs a restart (below) |
Error that needs a restart
-
Stop the buzzer and note the code
Press any key. Write down the number after the E.
-
Clear the cause
Remove scraps of film or anything in the carriage or feed path, and check any part you just replaced is fitted correctly.
-
Restart
Power off, wait a short while, power on. If the same code returns, contact us with it.
Nozzles won't come back after cleaning
-
Clean the right head with the right strength
In Menu 3 Cleaning, pick the head with the gaps (or ALL). Run Normal or Long two or three times, then Little Charge if gaps remain.
-
Clean what touches the heads
Run CR Maintenance (Menu 1 Setup > Setup 20 CR Maintenance) and clean the wiper, caps and around the heads with dry cleaning sticks. Our daily and weekly guide shows how.
-
Check worn parts
Replace the cleaning wiper every six months, and the flushing box absorber when ink lumps rise above its frame.
-
Keep printing while you call
If Little Charge doesn't recover them, Setup 21 Select Nozzle lets the printer use only the nozzles that fire. Contact us with your nozzle check.
If the film lifted and the heads dragged across it, the coating on DTF film can gel ink on the nozzles. Stop printing and text us before running more cleanings.
Other print problems
| Symptom | Check |
|---|---|
| Colors lean the wrong way (grays print green) | Nozzle check for gaps, ink within its date, and each bag's color matching its S/C card and slot. A mismatch needs Longstore and Initial Charge to fix |
| White doesn't line up under color | Run head alignment and print quality adjustment from the calibration menus, then a media feed adjustment |
| Carriage pauses at the sides | Category 6 Gigabit Ethernet cable, and MPS enabled in MSM |
| Smears or missing patches | Wrinkled or damp film, dirt around the heads, or film warped by the heater (increase Start Feed) |
Clearing a film jam
Power off with a long press. Open the front cover and slide the carriage off the film to the right; if the head height is Low, Mutoh says to switch it to High first and back afterward. Slide the edge holder off, pull the media feed lever toward you, cut away the damaged film along the groove, rewind a little with the flange, remove scraps, power on and print a nozzle check.
Text us a photo or short video at (562) 609-4996 if the message isn't listed here.
Watch STS: CR Maintenance on the XPJ-1682D
Embedded from the manufacturer's official channel.
Common questions
The printer stopped printing and says Shake W Cartridge.
Agitate the white ink bags. Mutoh says if you ignore the message for 12 hours, the printer stops printing until you do.
What does Check Ink mean?
The printer isn't detecting that slot's ink pack adapter. Pull it out and push it fully back in. If the message stays, contact us.
My grays print green but the nozzle check is complete.
Check the ink is within its date and that every bag's color matches its S/C card and slot. Then run print quality adjustment. If it continues, text us a photo.
The white layer is shifted from the color.
That is alignment, not clogging. Run head alignment and print quality adjustment from the calibration menus, then media feed adjustment.
Can I stop the E-code error from coming back?
Clear any obstruction and restart. If the same code repeats, Mutoh says a technician is needed, so contact us with the code.
- STS XPJ-1682D Operation Manual
- Mutoh Status Monitor (MSM) Operation Manual
- AA support requests about XPJ-1682D errors, print quality and connection, 2024 to 2026











































































