Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPJ-1682D daily and weekly maintenance: white agitation, Sleep Mode, wiper and capping unit cleaning
Keep the XPJ-1682D powered on in Sleep Mode when you're not printing, agitate the white ink bags whenever the panel shows Shake W Cartridge, and print a nozzle check before and after each day's work. Once a week, put the printer in CR Maintenance and clean the cleaning wiper and the rubber around the capping units with a dry cleaning stick. Clean inside once a month.
Every day
-
Keep it on and in Sleep Mode
When you're done printing, leave the power on and start Sleep Mode: Menu 6 Sleep Mode > Sleep Mode 2 Start, then Enter. Set how it cleans under Sleep Mode 1 Cleaning Setting: Short, Normal or Long, on a timer from 1 to 24 hours (default Short every 6 hours). Tap Enter to wake it.
-
Agitate the white ink when asked
The panel shows Shake W Cartridge every 12 hours. Pull the white high-capacity ink pack adapter out of its slot, wipe ink off the insertion point with a paper towel, and soak up any ink around the tube connectors with a cleaning stick. Holding one hand on top of the bag so it stays attached, turn the plug up and hold 3 seconds, then turn it down and hold 3 seconds. Do that 10 times, then push the adapter back into the same slot all the way.
-
Nozzle check before and after printing
With film loaded, print Nozzle Check F from the panel (Menu 2 Test Print). If lines are missing or thin, run a Short or Normal head cleaning from the panel and check again. If Normal doesn't clear it after several tries, use Long, then clean the wiper and around the head (below). Little Charge, under Menu 3 Cleaning, is the last step and uses a lot of ink.
Every week
-
Put the printer in CR Maintenance
Tap Home, open Menu 1 Setup, step to Setup 20 CR Maintenance, and tap Enter at Start -> Enter. The carriage moves to the left and the wiper rises.
-
Clean the cleaning wiper
Open the front cover and the right maintenance cover. With a dry cleaning stick, wipe the left side of the wiper back and forth, then the right side. If a stain won't come off, run a Short cleaning and try again.
-
Clean around the capping units
With a fresh dry stick, clean ink and dust from the rubber around both capping units. Do not touch the absorber inside the caps.
-
Finish
Close both covers, tap Enter at CR Maintenance End -> Enter, then tap Home.
Use cleaning sticks dry, once, and without touching the tip. Finish within about 5 minutes. A damp, reused or dried-out stick can damage the print head. Never touch the print head surface.
When nozzles won't recover: around the print head
In CR Maintenance, open the front cover and the left maintenance cover. Clean ink and dust from the silver metal around each head, the gap between the head and its guide, and the black plastic head guide. Don't touch the head surface.
Every month: inside cleaning
Remove the media, turn the printer off and unplug it. Let the platen cool if it's hot. Brush dust off the pressure rollers with a soft brush (no canned air). Wipe ink off the platen, media guide and edge holders with a soft cloth lightly dampened with ethanol of 50% or higher, wearing gloves.
As needed
- Waste ink tank: empty it when it's more than half full or the panel shows Full WasteInkTank. It holds 2,000 ml, so use a container at least that big, open the waste valve, then close it securely and wipe the opening.
- Flushing box absorber: replace it when ink lumps rise above the frame, roughly every two months.
- Color sensor: if automatic print quality calibration keeps failing, clean the sensor glass gently with a stick dampened with ethanol.
- Cleaning wiper: Mutoh lists it as a user-replaceable part every six months. Text us before your first one and we'll walk you through it.
If the panel shows a Life Times message for the pump or a motor, or an error that needs a restart keeps returning, that's a technician job. Text us a photo of the panel at (562) 609-4996.
Watch STS Inks' video: CR maintenance on the 1682 DTF printer
More videos
Embedded from the manufacturer's official channel.
Common questions
What happens if I ignore the Shake W Cartridge message?
For 12 hours after it appears, the printer keeps making you wait before it prints. After 12 hours it won't print at all. Agitating the white ink clears it either way.
Can I turn the printer off at night?
Mutoh says no. Leave it on and start Sleep Mode from Menu 6. In Sleep Mode it circulates ink and runs head cleanings on a timer (Short every 6 hours by default).
I'll be closed for two weeks. What do I do?
If someone can come in, once a week agitate the ink, wake the printer, print a nozzle check and put it back to sleep. If nobody can, run Longstore and power off, which the manual rates for storage up to one month. For more than a month, contact us first.
Why didn't the printer clean itself overnight?
Sleep Mode skips cleanings if a cover is open, the pressure rollers are released, the waste ink tank is full, an ink pack adapter or S/C card is out, or the S/C card isn't genuine. Check those first.
Can I swap two white ink adapters between slots 7 and 8?
No. The manual says to put each adapter back in its original slot, even when both hold the same color.
- STS XPJ-1682D Operation Manual
- STS XPJ-1682D Startup Guide
- AA support requests about XPJ-1682D maintenance and white ink, 2024 to 2026










































































