Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPJ-1682D ink bags: checking levels, replacing a bag and S/C card, and the Change Plug message
On the XPJ-1682D, check levels under Setup 16 Ink Status. To change ink, pull the slot's ink pack adapter, lower its lock lever, swap in a new bag agitated 10 times, fit the new bag's S/C card, confirm the lock through the window, and return the adapter to its original slot. When the panel says Change Plug, use the sealing jig and a fine tool to fit a new plug before it leaks.
Check your ink levels
Tap Home, open Menu 1 Setup and step to Setup 16 Ink Status. Each slot shows 0 to 100%. The slots are 1 Black, 2 Cyan, 3 Magenta, 4 Yellow, 5 Light Cyan, 6 Light Magenta, 7 White and 8 White. A level blinking at 10% means that slot is in smartchip recovery, and you should judge the real level by eye.
When ink runs low, the error light flashes, the buzzer sounds and the panel shows [slot] S/C Ink Low. Tap Enter to stop the buzzer and get a new bag ready. When it runs out you'll see Ink End or S/C Ink End, and the printer won't print again until you change the bag.
Replace an ink bag
-
Gear up
Wear gloves and eye protection. If the new bag came from a cold place, let it sit at room temperature for at least three hours first.
-
Remove the adapter
Tap Enter to stop the buzzer, then pull the high-capacity ink pack adapter for that slot out of the printer.
-
Take out the empty bag
Lower the lock lever on the adapter and detach the empty bag. Remove its S/C card. Bag the empty in plastic and dispose of it under local rules.
-
Agitate the new bag
Turn the ink plug up and hold 3 seconds, then turn it down and hold 3 seconds. Repeat 10 times.
-
Fit the S/C card
Slide the S/C card that came with the new bag into the tabs on the adapter.
-
Insert the bag
Hold the adapter's lock lever down and push the bag fully into the adapter. Look through the observation window: the lock should sit at the top of the bag's neck.
-
Check the lock lever
The lever must spring back to its original position. If it doesn't, push it up with a finger. If it still won't return, take the bag out and insert it again. A lever left down can leak.
-
Return the adapter to the same slot
Match the color label on the printer and push the adapter all the way in. Always use its original slot, even if another slot holds the same color.
Always fit the new S/C card that came with the new bag. A reused card makes the printer count ink wrongly. And if you don't have a replacement yet, leave the empty bag in place: an empty slot can clog the heads.
When the panel says Change Plug
The rubber plug where each adapter connects wears out. When it does, the status LED turns red and the panel shows [slot] Change Plug OK -> Enter. Mutoh says running on a worn plug can leak ink. You need a new adapter plug, the sealing jig that came with the printer, a fine-tipped tool such as a precision screwdriver, a cleaning stick, paper towels, gloves and eye protection.
-
Acknowledge and remove
Tap Enter, then pull out the adapter for that slot.
-
Clean it
Wipe ink off the adapter's insertion point with a paper towel. Tilt the adapter (caution label down, insertion end slightly lowered) and soak up ink around the tube connectors with a cleaning stick.
-
Swap the bag for the sealing jig
Lower the lock lever, detach the ink bag and wipe around its opening. Then, holding the lever down, push the sealing jig fully into the adapter and check through the window that it is seated. The jig stops ink running out of the tube.
-
Free the tube connector
Use the fine tool to push the tube connector out through the left gap of the adapter, taking care not to damage it. Lay the adapter on its side, caution label up.
-
Replace the plug
With the fine tool, ease the old plug off the tube connector. Keep the opening pointing up so ink can't run out, and don't bend the tube. Push the new plug in halfway, then all the way. Turning it with a finger helps.
-
Reassemble
Clip the tube connector securely back into the adapter's tabs. Remove the sealing jig and wipe it, and keep it for next time. Refit the ink bag as above and return the adapter to its slot.
No spare plug? Leave the adapter in the printer and replace the plug as soon as you can, because an empty slot can clog the heads. Text us a photo or short video at (562) 609-4996 if a lever won't latch or ink leaks after the swap.
Common questions
Can I reuse the old S/C card with a new bag?
No. Mutoh says to replace the S/C card with the new one supplied with each bag, or the printer won't detect the ink level correctly.
Should I pull the empty bag while I wait for ink?
No. Mutoh says not to remove an empty bag if you have no replacement, because that can clog the heads.
The lock lever won't go back up.
Push it up with a finger. If it still won't return, take the bag out and insert it again. A lever left down can leak.
How often does the plug need changing?
When the printer tells you. The panel shows Change Plug and the status LED turns red when that slot's plug reaches its end of life.
I use 500 ml cartridges, not bags.
Mutoh's manual describes bags in high-capacity adapters. If your setup looks different, text us a photo before changing anything.
- STS XPJ-1682D Operation Manual
- AA support requests about XPJ-1682D ink and cartridges, 2024 to 2026










































































