Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa GoSign for the S Class 3 and S One: setting up materials (media profiles) and running cut-only jobs
In GoSign, set up each vinyl once in the Material manager: a material holds methods (such as kiss-cut), each linked to a tool with its speed, overcut and FlexCut settings. For a job, import the file, run the clean-up tools, check the Layers window from top to bottom (material, cutter, method and tool), make one-off changes there, then output with copies, weed box and cut-off as needed.
How GoSign thinks about a job
GoSign sits between your design software and the cutter. Instead of typing knife settings for every job, you build a library of materials (Summa's videos call them media profiles). Each material has methods (what you want done, such as kiss-cut), and each method is linked to a tool with its own parameter sets. Pick the material and GoSign chooses the right tool and settings. GoSign runs on Windows; Mac users use Summa's MacSign plug-in instead.
Set up a material once
-
Open the Material manager
Click the Material manager tab in the ribbon. This tab sets the defaults. It is not where you make one-off changes for a single job.
-
Create or duplicate a material
Create a new material, or duplicate a similar one and edit it. Give it a clear name and category, and use the description for anything the operator should know about the material.
-
Link methods to tools
For each method, click the cross-hatched area to see its tool. Click a tool to link it, or click a highlighted tool to unlink it. Then set that tool's parameters. For knives that is the speed (slower for thicker material), overcut (cuts slightly past each corner to help weeding; keep it small for designs with lots of small curves), and FlexCut for cutting through.
-
Set a default and back it up
Mark the material you use most as the default; GoSign uses it whenever the file doesn't name a material. Then use Backup on the General tab to save the material manager, so you can restore it or move it to another computer.
Run a cut-only job
-
Import the file
The basic version opens SGSJ, PDF, DXF, OXF, SGP and SVG files. The Pro Pack adds PLT, HPGL, DMPL, i-CUT and ZCC. For PDF, Summa recommends separating methods by layer; for DXF, by colour.
-
Clean up the vectors
On the Job tab, Close objects closes any open shapes and Reduce nodes thins out over-detailed curves. There are also tools to remove double lines and double objects and to turn brush strokes into a single cut line. Each has a maximum distance of 3 mm, and Summa warns that higher values lose more cut quality. The default import action already does some of this.
-
Check the Layers window, top to bottom
Check the material first, then the cutter, then the method and tool for each layer. Work from the top down, because each choice can change everything below it. A simple cut-only job usually has one layer. Any lines with an unknown method get the kiss-cut tool by default.
-
Tweak for this job only
Change parameters in the Layers window for a one-off job. If the change should stick, use Save to material manager.
-
Fit the working area
With the cutter connected and media loaded, Fit working area to device sets the area to the loaded media.
-
Output
Run the output action set from the Action sets pane on the left. Before it cuts, GoSign shows the output options so you can change them for this job: number of jobs, copies per job (with Autofill to fill the width), a Weed box around the job, tiling, and what happens at the end, such as feeding the job length with a margin and cutting it off.
When the cut isn't what you expected
- Wrong pressure or speed: the job picked up the default material. Set the right material at the top of the Layers window.
- Some lines kiss-cut that should cut through: those lines had an unknown method. Assign the right method to that layer.
- Shapes cut twice or not closed: run the clean-up tools before output.
Our connection guide covers installing GoSign and adding the cutter. If GoSign can't see the cutter or the license won't activate, text us at (562) 609-4996.
Watch Summa's video: setting up a cut-only job in GoSign
More videos
Embedded from the manufacturer's official channel.
Common questions
What is a media profile in GoSign?
Summa's manual calls it a material. It stores the methods and tool settings for one type of media, so you pick the material instead of typing settings each time.
Where should I change settings for just one job?
In the Layers window, not the Material manager. Use Save to material manager only if the change should become the default.
What files can GoSign open?
The basic version opens SGSJ, PDF, DXF, OXF, SGP and SVG. The Pro Pack adds PLT, HPGL, DMPL, i-CUT and ZCC.
Why did part of my job only kiss-cut?
GoSign gives the kiss-cut tool to any lines whose method it doesn't recognize. Set the method for that layer.
Does GoSign run on a Mac?
No, it is Windows software. Summa offers the MacSign plug-in for Mac users.











































































