Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Connecting a Summa S Class 3 or S One cutter to your computer: USB, Ethernet, Wi-Fi and GoSign
On Windows, install Summa's USB driver before you plug the cutter in, with an administrator account and UAC set to its lowest level. On a Mac no driver is needed, because the cutting software carries it. For a network connection, use a shielded CAT6 cable and give the cutter a fixed IP address in Configuration > Ethernet, then reboot it. Current S Class 3 and S One cutters are meant to be driven from Summa GoSign V4.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Windows doesn't recognize the cutter on USB | Driver not installed first, or no admin rights | Step 2 |
| Software can't find a network cutter | IP address changed, or wrong address in the software | Step 3 |
| Message says Wi-Fi isn't available in your region | Wi-Fi isn't offered there | Step 4 |
| Wi-Fi menu asks for a code | Wi-Fi not activated yet | Step 4 |
| Jobs go nowhere with two cables plugged in | The other port took the connection | Step 1 |
Step by step
-
Pick one connection
The S Class 3 and S One both have USB and Ethernet ports, and Wi-Fi as an option. If USB and Ethernet are both plugged in, the port that receives data first stays active and the other one is shut off. Pick one connection and stick with it, so you always know where your jobs are going.
-
USB on Windows: driver first, cable second
Log in with an administrator account and set User Account Control to its lowest level. Switch the cutter off. Download and install the USB driver for your model from Summa's software and firmware page. Then connect the cable (USB A on the computer, USB B on the cutter, 5 m or 16 ft at most), switch the cutter on and let Windows finish installing the device. Restart the computer.
If you plugged the cutter in before running the installer, leave the cutter connected and switched on and run the installer then. Windows should detect the cutter and pick the right driver.
On a Mac, current cutting software does not need a separate driver.
-
Ethernet: use a fixed IP address
Use a shielded CAT6 cable. Ask whoever runs your network for a free address and the subnet mask. Summa recommends a fixed (static) address. On the touch screen open the menu, scroll to Configuration > Ethernet, set DHCP to Off, then enter the IPv4 address and the Subnet mask, confirm each one and reboot the cutter. Enter the same address in your cutting software.
If you prefer DHCP, set it to On and reboot. The address the network assigns shows on the cutter's main screen. It can change if the cutter is unused for longer than the DHCP lease time, which is the usual reason a network cutter suddenly goes missing.
-
Wi-Fi: activate it first
Wi-Fi is switched off from the factory and is only offered in some regions (the S One manual names Europe, the US and Canada). To turn it on, tap the machine information button to read the serial number, register the cutter on Summa's product registration page, and enter the 6-digit activation code you receive under Configuration > Wi-Fi. Keep the email with the code. The same code unlocks the OPOS barcode feature. Then choose your network, enter the password, and set a fixed IP address the same way as for Ethernet if your network allows it.
-
Install the software
Summa's own software for these cutters:
- GoSign V4: Summa's cutting and print-and-cut software for the S Class 3 (firmware MD9987 revision 22 or later) and S One cutters from 2019 or later (firmware MD9986 revision 20.4 or later). Windows 10 or 11, Professional or Enterprise, 64-bit.
- GoSign Tools: plug-ins for CorelDRAW, Illustrator and Inkscape that send jobs to GoSign.
- MacSign: Illustrator plug-ins for cutting straight from a Mac. It is registered with your cutter's serial number.
- Summa Cutter Control: Windows utility for changing cutter parameters, saving user configurations and running the OPOS barcode server.
The firmware revision is shown on the machine information screen. If your cutter is older than GoSign V4 needs, contact us before you update firmware.
-
Send a test job
Load media, set your knife (see the knife guide for your model), then send a small cut from GoSign. If nothing arrives, check that the cutter is online on its main screen. Touching the menu takes the cutter offline and pauses it until you return to the main screen.
Still not connecting?
Text us at (562) 609-4996 with your cutter model, firmware revision, how it's connected and a photo of the cutter's main screen, and we'll walk you through it.
Watch Summa's video: connecting the S3 cutter to GoSign
More videos
Embedded from the manufacturer's official channel.
Common questions
Can I use USB and Ethernet at the same time?
Both can be plugged in, but only one works at a time. Whichever port receives data first stays active and the other is switched off.
My cutter worked yesterday over the network and now GoSign can't find it. Why?
If the cutter gets its address from a DHCP server, the address can change when the cutter sits unused longer than the server's lease time. Check the IP address on the cutter's main screen and update it in your software, or set a fixed IP address on the cutter.
Which GoSign version do I need?
Summa says GoSign V4 is for the S Class 3 with firmware MD9987 revision 22 or later, and for S One cutters from 2019 or later with firmware MD9986 revision 20.4 or later. GoSign V3 still runs these cutters, but Summa strongly recommends moving to V4. Both need Windows Professional or Enterprise, not Home.
Does Wi-Fi work out of the box?
No. Wi-Fi is an option that is switched on with an activation code from Summa's product registration page, and it is only offered in some regions. The same code switches on the OPOS barcode feature.
Can I cut without a computer?
The S Class 3 can cut a file straight from a FAT32 USB flash drive through Actions > Open File. Summa says it only accepts cut files made by cutter software: .plt, .dmpl, .hpgl or .summa1.
- Summa S Class 3 User's Manual (Rev 006)
- Summa S One User Manual (Rev 001, distributor copy)
- Summa software and firmware downloads
- Summa product registration
- AA support requests about Summa cutters, 2024 to 2026











































































