Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S Class 3 cutting jobs off the roll: separation knife blade, cut-off margin, recut copies and sheet mode
The S Class 3's separation knife is a magnet-held razor blade in a holder under the tool carriage: undo the knurled screw, turn the blade around or replace it, and refit it at the same tilt. Use it only on standard vinyl up to 0.25 mm. The cutter feeds by the Cut-off margin (10 mm by default) before cutting a job off, and Recut repeats the last job at the Recut offset (40 mm by default).
Ways to get a finished job off the roll
| You want to | Use |
|---|---|
| Cut the job off automatically | Separation knife plus the software's Cut off command |
| Cut off right now | The cut-off button or Actions menu |
| Make blank sheets from a roll | Cut off sheets |
| Repeat the last job down the roll | Recut and Recut offset |
| Cut the same job on loose sheets | Sheet mode |
The separation knife is a razor blade. Summa says to use it only on standard vinyl up to 0.25 mm thick.
Turn or replace the separation knife blade
-
Remove the holder
Turn the knurled screw at the bottom of the tool carriage and take out the razor blade holder.
-
Turn or swap the blade
A small magnet holds the blade in place. When it gets dull, turn it around to use the other edge, or replace it.
-
Refit it the right way
The assembly sits tilted at about 30 degrees when it is mounted on the machine. Note its position before you take the blade out so it goes back the same way.
Cutting jobs off
- From the software: when your cutting software sends a Cut off command, the cutter feeds forward by the Cut-off margin and then cuts. The default margin is 10 mm. In GoSign this is the Cut off option under the end-of-job settings.
- By hand: Actions > Cut off cuts the loaded material at the current position of tool 1. The Set Origin screen also has a cut-off button that cuts off the previous job, then finds the front of the media and sets a new origin.
- Blank sheets: Actions > Cut off sheets cuts a set number of sheets of a fixed length from the roll.
Repeating a job
-
Set the gap
Open the menu, scroll to Configuration, tap Recut offset, set the distance between copies and confirm. The default is 40 mm. Go back online.
-
Cut the first copy
Send the job as usual. The cutter stops and goes online again when it finishes.
-
Recut
Open the menu, tap Actions, scroll to Recut, enter the number of copies and confirm. The last job (if it still fits in the cutter's memory) is cut again, one copy after another.
If you use recut and cut-off together, the recut offset must be larger than the cut-off margin. For OPOS print and cut jobs that use cut-off, Summa says the recut offset must be at least 30 mm larger than the cut-off margin. For cut-only work, Summa recommends your software's multi-copy feature, which nests copies to save media.
Same job on many sheets
-
Turn on Sheet mode
Open the menu, tap Actions, scroll to Sheet mode, tap On, confirm and go back online.
-
Cut the first sheet
Send the job. The cutter stops and goes online again.
-
Swap sheets the same way every time
Raise the pinch rollers, take out the sheet, slide in the next one in exactly the same position and orientation, and lower the rollers. The cutter remembers where the sheet sat relative to the pinch rollers and the front of the cutter. An edge of the base plate and the side of a pinch roller assembly make easy reference points.
If the separation knife leaves a ragged edge even with a fresh blade, or doesn't reach across the media, text us at (562) 609-4996.
Common questions
What can the separation knife cut?
Summa says standard vinyl up to 0.25 mm thick only.
The cut-off edge is ragged. What do I do?
Take out the holder and turn the razor blade around to its fresh edge, or replace it if both edges are worn.
Why does the cutter feed forward before cutting the job off?
That is the Cut-off margin, 10 mm by default, set under Configuration.
My recut copies overlap the cut-off. Why?
The recut offset must be larger than the cut-off margin, and for OPOS jobs at least 30 mm larger.
Does the S One have a separation knife?
Not in the S One manual. GoSign notes that on a cutter with no cut-off knife, FlexCut is used to cut jobs off.











































































