Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S Class 3 and S One FlexCut: cutting through vinyl and backing with tear-off bridges
FlexCut alternates a length cut at full pressure (through vinyl and backing) with a short length at reduced pressure that leaves a bridge. Find the pressure that just cuts through everything and the pressure that cuts only the vinyl, enter them as Full pressure and Flex pressure, start with 10 mm full length and about 1 mm bridge, and test. After that, tune only the bridge length.
What FlexCut does
FlexCut cuts all the way through the vinyl and its backing, but every so often it eases off the pressure for a short distance. Those short stretches leave tiny bridges that hold the job together while it moves back and forth through the cutter. When the job is done, you tear the pieces out. It is meant for simple shapes such as rectangles, usually around a contour cut (kiss-cut stickers that are then cut out as individual pieces).
Match your symptom
| What you see | Most likely cause | Fix |
|---|---|---|
| Pieces fall out or catch while cutting | Bridges too short or too weak | Raise flex pressure length |
| Pieces won't tear out cleanly | Bridges too long | Lower flex pressure length |
| Full-pressure sections don't go through | Pressure too low, knife worn or not out far enough | Redo step 1 |
| Ragged cuts at high pressure | Speed too high | Lower FlexCut velocity |
| First line comes loose and jams | Parallel lines too close | Space lines at least 1 cm apart |
Find your two pressures
-
Set the knife for cutting through
For FlexCut the knife is turned out just far enough to cut through the vinyl and the backing, and no further. On a tangential (T or TC) S Class 3, Summa recommends letting the nosepiece touch the media at full pressure. On a drag knife, let the holder rest on the media at full pressure unless the material scratches easily.
-
Find the cut-through pressure
Run the normal knife pressure test and raise the pressure until it cuts completely through vinyl and backing. Then turn the knife in a little and test again; keep going while it still cuts through. Then lower the pressure a little at a time while it still cuts through. Write down that pressure. From here on, don't change the knife depth unless the blade wears.
-
Find the vinyl-only pressure
Lower the pressure until it cuts just the vinyl and not the backing, and write that value down too.
Enter the FlexCut settings
Open Menu > FlexCut on the touch screen. The FlexCut menu only appears when a drag or tangential knife is selected as the tool.
- Full pressure: your cut-through value.
- Full pressure length (cut length on the S One): start at 10 mm.
- Flex pressure: your vinyl-only value.
- Flex pressure length (cut length on the S One): this is the bridge. Summa's starting point is 1 mm on the S Class 3 and 0.8 mm on the S One.
- FlexCut velocity: set separately from normal speed. Summa advises against going over 400 mm/s (16 ips) once pressure is above about 170 g, so slow it down for heavy pressures.
- Panel size: FlexCut is cut in panels. Summa recommends 3 to 10 cm. On the S Class 3 it is at the bottom of the FlexCut menu; on the S One it is under Settings > Panel > Panel size. Use a smaller panel for weak material.
- S Class 3 only, Grid Cut: cuts straight lines as a grid, vertical lines first and then horizontal lines front to back, to avoid damaging or jamming the material.
- S One only, FlexCut mode: Off, Fast or Accurate. Fast is quicker but less precise because pressure changes on the move; Accurate stops at every pressure change.
FlexCut values are always in metric, whatever units the cutter is set to. On the S Class 3, tap the test button to cut the internal FlexCut test pattern.
Test and tune
-
Check the bridges
If the bridges are too large, test again with a shorter flex pressure length. If they are too small or missing, make it longer. Lowering the speed can also help.
-
Only change the bridge length after that
Once it works, Summa says to adjust only the flex pressure length. Don't touch the pressures again until the knife wears; then start over from the first section.
-
Send the job
Many cutting programs, GoSign included, send the contour lines first and then switch FlexCut on for the cut-through lines. Summa still says to set the FlexCut values on the cutter rather than in the software. If your software can't switch modes, send the contour lines on their own, switch the cutter to FlexCut, then send the cut-through lines.
Keep parallel cut-through lines at least 1 cm (0.4 in) apart. Closer than that, the first strip can come loose while the second line is cut and cause a jam.
Material with no backing
FlexCut works on single-layer material, but it takes more trial and error. Only the full pressure is easy to find. Plastics usually need a fairly high flex pressure and short bridges; fibrous materials need a lower flex pressure and longer bridges. Summa notes that some materials simply can't be cut through with a good result.
If you can't find a setting that holds together and still tears out, text us a photo of the test at (562) 609-4996 with the material name.
Watch Summa's video: setting up FlexCut on the S3
More videos
Embedded from the manufacturer's official channel.
Common questions
What does FlexCut do?
It cuts through the material for most of the line but leaves short bridges at reduced pressure, so the job holds together on the cutter and the pieces tear out afterward.
My pieces won't tear out. What do I change?
Shorten the flex pressure length (the bridge). Summa says that is usually the only setting to adjust once the pressures are right.
Why is FlexCut missing from the menu?
It only appears when a drag or tangential knife is selected as the tool, not a pen or creasing tool.
Should I set FlexCut in GoSign or on the cutter?
Summa recommends setting the FlexCut values on the cutter, even if your software switches FlexCut on.
How fast can I cut?
Summa advises staying at or below 400 mm/s (16 ips) when the pressure is above about 170 g.











































































