Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S Class 3 loading media: pinch rollers, media sensors and fixing tracking problems
Feed the media from the back, lay the left edge over the far-left grit roller and the right edge over the long grit roller, and click the outer pinch rollers into place about 3 to 15 mm in from each edge. Make sure the media runs straight, then lower the pinch rollers: the carriage measures the width by itself. If media slips, clean the silver drive sleeves. If it isn't detected, clean the media sensors or calibrate them for dark-backed or clear media.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Media walks sideways or skews | Pinch rollers off the grit rollers, crooked feed | Steps 2 to 4 |
| Media slips, lengths come out short | Dirty drive sleeves | Step 7 |
| Cutter says no media is loaded | Dirty or uncalibrated media sensors | Step 6 |
| Job stops and carriage parks right | Pinch rollers raised mid-job | Step 5 |
| Roller marks on soft media | Full pinch pressure | Step 5 |
Step by step
-
Mount the roll
Raise the pinch rollers with the lever on the right, next to the touch screen. Loosen the knobs on both core holders, push one into each end of the roll and tighten them. Set the roll on the support rollers with the core holders sitting in the grooves of the guides. Summa doesn't recommend running a roll without the core holders, because it can't guarantee accurate feeding that way.
-
Thread the media
Feed the media in from the back, under the pinch rollers, toward the front. Lay the left edge on the far-left grit roller and check that the right edge lies over the long grit roller. Both edges must sit on a grit roller. If the media is too narrow to reach the long grit roller, put the left edge on the second grit roller from the left instead.
-
Place the pinch rollers
Slide the outer pinch rollers, holding them by the sides at the front of the cutter, until they click into position over a grit roller about 3 to 15 mm (0.1 to 0.6 in) in from each edge. The right roller goes over the longest grit roller. The middle roller or rollers can be switched on or off; when off they stay up.
-
Straighten and lower
From the front, pull the media gently while holding the roll so it's tight, and slide the roll and guides along the support rollers until the media runs in a straight line to the cutter. Then use the lever to lower the pinch rollers onto the media. After a second, the carriage moves right to left to measure the width. Let the cutter unroll media itself; don't pull lengths off by hand. Sheets load the same way; roll a long sheet up first so it feeds like a roll.
Raise the pinch rollers whenever you finish for the day. Left down, they develop flat spots that ruin tracking. Raising them during a job stops the job immediately.
-
Lighter grip for delicate media
The outer pinch rollers have a standard and a low pressure. Set Configuration > Autoload to Ask so the cutter waits before loading, load the media, then push the caps of the two outer rollers up and inward. Pressure goes back to standard every time the rollers are lifted.
-
Media not detected
The cutter has one front media sensor and, at the back, one sensor on the 75 and two on the 120, 140 and 160. It uses them to find the media edge and to stop at the end of a roll, which protects the cutting strip and blade. Wipe the sensors with cotton swabs first. If a particular media still isn't seen (Summa names black-backed and transparent media), use Calibrations > Calibrate media sensors: pick the back or front sensor, half-cover it with the media as prompted and tap Measure. Set the sensitivity so the bar shows (almost) black when covered and (almost) white when uncovered, with the trigger slider about halfway. The calibration is stored per user configuration, so save it under a user you keep for that media.
-
Clean the drive sleeves
Backing residue builds up on the silver grit sleeves and cuts traction. Unplug the cutter, apply a mild glue-residue remover to the dirty sleeves, give it time to soften the build-up, then scrub with a brush (Summa suggests a toothbrush).
Still drifting?
If the media still walks with clean sleeves and correctly placed rollers, text us a short video of a long feed at (562) 609-4996 with the model and media type.
Watch Summa's video: loading media on the S3D, S3T and S3TC
More videos
Embedded from the manufacturer's official channel.
Common questions
Should I pull extra media off the roll before cutting?
No. Summa recommends letting the cutter unroll media itself during loading. With Autoload set to Off, Summa says tracking is no longer guaranteed.
Why should I raise the pinch rollers at the end of the day?
Left down for a long time, the rollers get flat spots, which Summa says seriously hurts tracking and cut quality.
The cutter says there's no media, but there is. Why?
The rear media sensors may be dirty or unable to see that media. Clean them with cotton swabs. Black-backed or transparent media may need Calibrate media sensors. On 120, 140 and 160 models, if both rear sensors are uncovered after loading, the cutter assumes nothing is loaded.
Can I cut outside the pinch rollers?
Actions > Load wider lets you extend the cutting width past the pinch rollers, but Summa says accurate tracking isn't guaranteed in that mode.
My thin or delicate media shows roller marks. What can I do?
Use the reduced pressure on the outer pinch rollers. Set Autoload to Ask, load, then push the caps of the two outer rollers up and inward. Pressure goes back to standard each time the rollers are lifted.
- Summa S Class 3 User's Manual (Rev 006)
- AA support requests about Summa media loading and tracking, 2024 to 2026











































































