Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S Class 3 OPOS contour cutting: printing marks, calibration and marks not found
Print the job and its OPOS marks with at least 2 cm (0.8 in) margin at the sides and front and 4 cm (1.6 in) at the end, and keep cut lines just inside or outside the artwork, never on its edge. If cuts are offset from the print, run Calibrate OPOS offset on black vinyl with white backing, and repeat it after every knife change. If marks aren't found on glossy or unusual media, run Calibrate media (OPOS) with a printed 4 x 4 cm square.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Cut line shifted the same way on every piece | OPOS offset needs calibrating | Step 4 |
| Marks not found, error during reading | Media or mark color hard to read, dirty media | Step 5 |
| Cut drifts more toward the end of long jobs | Too much back-and-forth feeding | Step 3 |
| Cut nicks the edge of the print | Cut line placed on the artwork edge | Step 1 |
| TC camera misses marks on shiny or dark media | Camera level needs setting | Step 6 |
Step by step
-
Set up the file
Create the artwork and the contour cut line. Most RIP and cutting software expects the cut line in a named spot color; check your software. Don't put the cut line exactly on the edge of the graphic, because the smallest movement will show. Summa suggests one of three things: put the line just inside the graphic, put it just outside, or add a thick border and cut inside it.
-
Print with room around the marks
Print the job and its OPOS marks from software that supports print and cut, and laminate afterward if needed. Leave 2 cm (0.8 in) at the sides and front and at least 4 cm (1.6 in) at the end of the roll or sheet. Short jobs can use smaller edge margins, but never less than 1 cm (0.4 in). Choose the alignment method (OPOS X, XY, XY2 or Xtra) in the software.
-
Load and cut
Load the printed media straight and with the pinch rollers set correctly, send the job, and position the sensor over the first mark when the cutter asks. The D and T models lower a sensor onto the media to read the marks; TC models switch on a light and read them with a camera. For long jobs, turn on panelling (Settings > Panels > Panelling) or use the software's panelling, not both. For repeated copies on one roll, leave at least 30 mm between copies.
-
Cuts offset from the print: calibrate OPOS offset
This teaches the cutter the distance between the knife tip and the sensor. Load black vinyl with white backing (Summa says it must be this combination), then go to Calibrations > Calibrate OPOS offset. The cutter cuts a square of about 9.5 x 9.5 mm and moves it forward. Weed the outer rectangle carefully so the edges stay clean, confirm, and the sensor reads the edges and calibrates itself. Repeat this after every knife change.
-
Marks not read: calibrate the media
The sensor is set at the factory for most media, but high-gloss and other unusual materials can need a media calibration. Print a square of at least 4 x 4 cm on the same media with the same ink as your marks. Load it, open Calibrations > Calibrate media (OPOS) and tap Measure. Move the sensor over an unprinted area and confirm, then over the printed square and confirm. The cutter shows a value for that media and mark color: write it down so you can enter it directly next time with Set. If you get an error, the sensor couldn't tell the two apart; check the test was done correctly. If reading doesn't improve, tap Reset to default.
-
TC models on reflective, black, clear or white media
If the media calibration can't give a usable value, open Calibrate media (OPOS) > Set with the camera over a mark and view what the camera sees. A complete, clean square means the value works. A broken or ragged square, or black showing outside the mark, means you need a different value: Summa says light marks on dark media usually need a negative value and dark marks on light media a positive one. Change it and check again.
Still missing?
Text us at (562) 609-4996 with a photo of the printed marks and of a miscut piece, your RIP and the media type.
Watch Summa's video: running a print and cut job in GoSign
More videos
Embedded from the manufacturer's official channel.
Common questions
Where do I choose OPOS X, XY or XY2?
In your print-and-cut software, not on the cutter. OPOS X uses marks down both sides; XY adds a line at the bottom to correct across the width; XY2 adds a line at the top too for large jobs; Xtra adds a line between each pair of marks.
Long jobs cut worse toward the end. Why?
Reading every mark first means a lot of back-and-forth feeding. Turn on panelling, either in the software or in Settings > Panels on the cutter, but not both.
What is the TC model's camera for?
TC models read marks with a camera (OPOS CAM) instead of a lowering sensor, which is faster. With GoSign and the Pro Pack it can also use round or cross marks and marks placed inside white areas of the job.
Media calibration made things worse. How do I undo it?
Open Calibrate media (OPOS) and tap Reset to default. Summa says to do that whenever a calibration doesn't improve reading.
Can it cut a whole roll of different jobs on its own?
Yes, with OPOS barcode. It needs a RIP that prints the barcode, a barcode server on the computer (Summa Cutter Control includes one) and the barcode option activated with a code from Summa's product registration.
- Summa S Class 3 User's Manual (Rev 006)
- Summa software and firmware downloads
- AA support requests about Summa contour cutting, 2024 to 2026











































































