Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S Class 3 or S One won't power on: power checks and replacing the fuses
First make sure the screen isn't just asleep: tap it once. Then check the rocker switch on the rear power entry module, the cord and a grounded outlet. If there is still nothing, unplug the cutter and check the two fuses in the power entry module. Summa specifies T2A 250V fuses only. If new fuses blow again, or the cutter stays dead with good fuses, stop and contact us.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Black screen with a Summa logo | Screen saver | Step 1 |
| Nothing at all, no light, no screen | Switch, cord, outlet or fuses | Steps 2 to 4 |
| New fuses blow again | Internal fault | Contact us |
| Powers on but behaves oddly afterward | Needs a check | Step 5 |
Step by step
-
Rule out the screen saver
After a while without use the touch screen goes blank and shows the Summa logo. The S Class 3 may show a tip instead, for example when the pinch rollers are left down. Tap the screen once. On the S Class 3, the light bar in the top cover also tells you the machine is on: blue when idle, green while working, red when there is an error that needs attention.
-
Check the switch and cord
The power switch is the I/O rocker on the power entry module at the back. Switch it off, check the cord is pushed fully into the power entry module and into a properly grounded wall socket, then switch it on. When it powers up, the touch screen comes on and the cutter initializes. If media is loaded, it measures and loads it.
Don't use a cord that is visibly damaged, and always unplug by the plug, not the cable.
-
Try another outlet
Plug something else into the same outlet, or plug the cutter into a different grounded outlet. Skip power strips and extension leads while you test.
-
Check and replace the fuses
Summa lets owners change the fuses. Disconnect the cutter completely from power first. Gently pry the release clips of the fuse holder in the power entry module until it pops out, take the holder out, and remove the two fuses. Fit new fuses of exactly the same type and rating, then click the holder back in.
Summa's rating is T2A 250V (time-delay, 2 amp). A higher-rated fuse removes the fire protection the fuse is there for.
-
Run the confidence test
Once it powers up, load a sheet of at least A3 or B size and run Actions > Confidence test. It is Summa's quick electrical and mechanical check, and it always cuts on the left side of the loaded media. A clean result means the cutter is working.
When to stop and call us
- New fuses blow straight away or after a short time.
- Good fuses, good outlet, and still no screen or light.
- You smell burning or see damage at the power entry module.
These point to the power supply or the mainboard, which is a job for a technician. Unplug the cutter and text us at (562) 609-4996 with the model and serial number from the back label.
Watch Summa's video: S Class 3 installation, including power-up
Embedded from the manufacturer's official channel.
Common questions
The screen is black with a Summa logo. Is it broken?
Probably not. Both cutters have a screen saver that blanks the screen and shows the Summa logo. Tap the screen once to wake it.
What fuses does it take?
Summa lists T2AH 250V for the S Class 3 and T2A H250V for the S One. That is a 2 amp, time-delay fuse. Never fit a higher rating.
I replaced the fuses and they blew again. What now?
Don't keep replacing them. A fuse that keeps blowing means something inside is faulty. Unplug the cutter and contact us.
How do I check the cutter works properly after a power problem?
Load a sheet of at least A3 or B size and run Actions > Confidence test. It is Summa's quick electrical and mechanical check and cuts on the left side of the media.
- Summa S Class 3 User's Manual (Rev 006)
- Summa S One User Manual (Rev 001, distributor copy)
- AA support requests about Summa cutters with no power, 2024 to 2026











































































