Support
Machine type
Brand
Summa S Class 3 vinyl cutter

Summa S Class 3 TC: installing the creasing tool or a second pen and setting tool 2 pressure

✓ Reviewed by Jason KimUpdated 2 min readFits: S Class 3 TC models (TC75 · TC160)
Short answer

On an S Class 3 TC, the front shaft (tool 2) takes the creasing tool, the S3 TC ballpoint tool or the fiber pen. Twist the tool in clockwise until firm, power on with media loaded, tap the tool icon until it shows "2", select the tool you fitted, then set and test the creasing pressure. The cutter can't sense which tool is fitted, and it uses one speed for both tools.

What the TC head adds

S Class 3 TC models have the performance (dual) head. It has two tool shafts, so a job can cut and crease, or cut and draw, without stopping to change tools. The rear shaft (tool 1) takes the same tangential knife, drag knife or pen as a T model. The front shaft (tool 2) sits inside the head cover; you only see its hole. TC models also read OPOS marks with a camera and a light instead of a lowered sensor.

Tools that fit the front shaft

  • Creasing tool D1.5 mm (Summa 395-758), for crease lines in carton and packaging materials. Summa lists it as standard with TC models.
  • Ballpoint tool for S3 TC (395-555), for drawing on various materials.
  • Fiber pen S Class T HD (395-376), for drawing on paper or cardboard.

Summa says the S Class 3 only performs to specification with genuine Summa tools.

Every tap on the touch screen can start a test or move the head and media. Keep your hands out of the cutting area while setting up tools.

Step by step

  1. Fit the tool

    Remove the black plug from the front tool shaft if it is still in. Gently insert the tool and turn it clockwise until it is firmly attached. Every front-shaft tool installs the same way.

  2. Read the tool number on screen

    Power on and load media. A small number now shows next to the tool icon. 1 means the screen is showing the rear shaft's tool and its pressure; 2 means the front shaft.

  3. Tell the cutter which tool is in shaft 2

    Tap the tool icon, select Creasing tool (or the pen you fitted), and confirm. The head has no sensor to identify tools, so this setting must match what is physically installed.

  4. Set and test the creasing pressure

    Tap the pressure, change it with the arrows or the keypad, and tap the test button to cut the internal creasing pressure test pattern. Confirm the value when the crease is right, or cancel to leave it unchanged.

  5. Mind the speed

    The cutter stores one speed for both tools. If the job will run the two tools at very different speeds, set the speed temporarily for the pressure test. During the real job, the speed comes from the software sending the job.

Good to know

  • After a power cycle, the screen shows whichever tool it showed before it was switched off. The cutter doesn't check the other shaft and may ask you to insert a tool if it needs one.
  • Whenever you change a tool, recheck its pressure and its own settings before cutting a job.
  • A standard T model has only the single tangential head. Creasing and a second tool need a TC model.

Summa's creasing video on this page walks through the design side, from file to finished box. If the crease test cuts through or barely marks the board, text us a photo at (562) 609-4996 with the board you are using.

Watch Summa's video: the S Class 3 creasing feature explained

Embedded from the manufacturer's official channel.

Common questions

Can I crease on a T or D model?

No. The second tool shaft is only on TC models, which have the performance head.

What do the numbers 1 and 2 next to the tool icon mean?

1 is the rear tool shaft (the knife position) and 2 is the front shaft. The screen shows the tool and pressure for whichever number is displayed.

Why does the cutter show the wrong tool after I restart it?

The head has no tool sensors. It shows whatever tool was displayed before power off, so always check it matches what is fitted.

Can I set different speeds for the knife and the creaser?

The cutter stores one speed for both. During a job, the speed comes from your software.

Is the creasing tool included?

Summa lists the D1.5 mm creasing tool (395-758) as a standard accessory with TC models.

Did this fix it?