Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S One drag knife: changing the blade, setting depth, pressure and knife offset
Summa ships the S One with the knife at zero depth, so turn it out before the first cut. Set the blade so the tip barely shows, run the knife pressure test until the vinyl is cut through and the backing is only lightly scratched, then set the knife offset with its own test. Repeat the offset every time you change the blade, and recheck depth and pressure for every new material.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| New cutter cuts nothing | Knife shipped at zero depth | Step 3 |
| Vinyl hard to weed, not cut through | Pressure or depth too low, worn blade | Steps 2 to 4 |
| Backing cut through | Blade out too far, pressure too high | Steps 3 and 4 |
| Rounded or overcut corners | Wrong knife offset | Step 5 |
| Pressure and offset seem to have no effect | Wrong tool selected | Step 1 |
The blades are razor sharp. Every tap on the touch screen can start a test or move the head and media, so keep your hands clear of the cutting area.
Step by step
-
Check the tool setting
Load media and look at the tool shown on the main screen. It must match what is in the clamp. To change it, tap Tool, pick Knife or Pen and confirm. Choosing the pen turns the knife offset off and switches to pen pressure, so a cutter left on Pen won't cut like a knife.
-
Take out the old blade
Loosen the head clamp screw and lift the knife holder out of the clamp. Turn the knurled adjustment knob clockwise to push the blade out of the holder, then pull it out carefully.
-
Fit the new blade and set the depth
Turn the knurled knob counterclockwise until the aluminium piece comes out of the plastic holder. Push the blunt, conical end of the new blade into the narrow end of the holder, then turn the holder upside down and tap it lightly on a hard surface so the blade seats fully. Turn the knob clockwise until the tip sticks out just as far as the material needs. For most vinyl the tip should be barely visible at the bottom of the holder; if you can clearly see it, it's out too far. Push the holder down into the clamp and tighten the screw.
-
Run the knife pressure test
Tap the pressure value on the main screen, set a value with the arrows or keypad, and tap the test button. Weed the test rectangle and look at the backing. You want the vinyl cut all the way through and the backing only lightly scratched on its coating. Thicker vinyl needs more depth, thinner vinyl less. Confirm the value when the test is right.
Never run with the blade cutting through the backing. Summa warns it seriously damages the rubber cutting strip and the blade.
-
Set the knife offset
Open the menu, tap Knife offset, set a value and run the test. Compare the cut corners with the correct, too low and too high pictures in the manual's knife offset section, adjust, and test again until the shape is right. Summa's typical starting values are 0.41 to 0.45 for standard blades, 0.9 to 0.97 for sandblast blades and 0.49 to 0.52 for the 60 degree blade. Do this every time you change the blade, and again when it starts to wear.
-
Test on scrap and save it
Cut a small real design on a scrap of the same vinyl. If you switch between materials, keep each one's settings in its own user configuration (the S One has 4) so you don't have to start over.
Still not right?
If the cut changes from one side to the other or along a long job with a fresh blade, the media is probably slipping or skewing: see our S One media loading guide. Otherwise text a photo of your weeded test at (562) 609-4996.
Watch Summa's video: changing the blade on the S1
More videos
Embedded from the manufacturer's official channel.
Common questions
My new S One won't cut. What's wrong?
Nothing. For safety Summa sets the knife depth to zero before shipping. Turn the knurled knob clockwise to bring the blade out, then run the pressure test.
What knife offset should I start with?
Summa's typical values are 0.41 to 0.45 for standard knives, 0.9 to 0.97 for sandblast knives and 0.49 to 0.52 for the 60 degree knife. Fine-tune with the offset test.
When should I use a sandblast knife?
Summa recommends it for material thicker than 0.25 mm.
Can I save different settings for different vinyls?
Yes. The S One has 4 user configurations. Tap the current configuration on the main screen to switch, and set pressure and offset in each one for a different material.
Can I use non-Summa blades?
Summa says the S One only performs to specification with a genuine Summa knife, pen or pouncing tool.
- Summa S One User Manual (Rev 001, distributor copy)
- AA support requests about Summa cut quality, 2024 to 2026











































































