Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S One loading media: pinch roller position, media sensor and fixing slipping or skewing
Use the core holders, feed the media from the back, and place the outer left pinch roller in a click position under a white triangle label and the right one over the long grit roller, each 3 to 15 mm in from the media edge. Pull the media tight, make it run straight, and lower the pinch rollers so the cutter can measure it. Slipping usually means dirty drive sleeves; media not seen usually means a dirty media sensor.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Media walks sideways or skews | Rollers off the grit rollers, crooked roll | Steps 2 to 4 |
| Media slips, cut lengths short | Dirty drive sleeves | Step 6 |
| Media not detected | Dirty media sensor, sensor off | Step 5 |
| Job stops, carriage goes right | Pinch rollers raised mid-job | Step 4 |
| Cuts poorly near one edge | Edge not over a grit roller | Step 2 |
Step by step
-
Mount the roll on core holders
Raise the pinch rollers with the lever on the right, next to the touch screen. Loosen the knobs on the two core holders, fit one into each end of the roll and tighten them. Set the roll on the supply rollers with each core holder sitting in the groove of its guide. Without core holders, Summa says tracking isn't guaranteed; if you must, keep the roll between the two guides.
-
Thread the media over the grit rollers
Feed the media in from the back, under the pinch rollers, to the front. Lay the left edge on the left-most grit roller and check that the right edge is over the long grit roller. Both edges must sit on a grit roller. If the media is too narrow to reach the long grit roller, put the left edge over the second grit roller instead and work the left pinch roller toward the long one.
-
Set the pinch rollers
With the rollers fully raised, slide them by holding the side of each assembly, not the back. Put the outer left roller in one of the click positions under a white triangle label and the outer right roller over the long grit roller. Each should be about 3 to 15 mm (0.1 to 0.6 in) in from the media edge. All pinch rollers must sit over a grit roller.
-
Tension, straighten, lower
Pull the media tight while holding the core holder at the back, and slide the roll and guides along the supply rollers until the media runs straight. Use the lever to lower the pinch rollers onto the media. After a second the carriage runs right to left to measure the usable width. Let the cutter unroll the media itself. Sheets load the same way; roll long sheets up first so they feed like a roll.
Raise the pinch rollers when the cutter isn't in use. Left down, they develop flat spots that Summa says seriously hurt tracking and cut quality. Raising them during a job stops it at once.
-
Media not detected
The rear media sensor finds the media and stops the cutter at the end of the roll. Wipe it out with a cotton swab. Then check that Configuration > Media sensor is On (the default). Summa says the sensor is there to protect the cutting strip and the blade tip, so leave it on.
-
Clean the drive sleeves
Liner residue clogs the silver drive sleeves over time, so the media slips between them and the pinch rollers. Unplug the cutter, put a mild glue-residue remover on the dirty sleeves, give it time to dissolve the build-up, then scrub with a brush (Summa suggests a toothbrush). Do every dirty sleeve.
Still drifting?
Text us a short video of a long feed at (562) 609-4996, with the model (D60 to D160) and the media you're running.
Watch Summa's video: loading media on the S1
More videos
Embedded from the manufacturer's official channel.
Common questions
The screen says "Insert media and lower the pinch rollers". What do I do?
That's the cutter's ready-with-no-media screen. Load media as in the steps and lower the pinch rollers; the carriage then measures the width.
Can I pull media off the roll by hand before a long job?
Summa recommends against it. With Autoload on, which is the default, the cutter unrolls what it needs. Summa says tracking isn't guaranteed with Autoload off.
Can I cut outside the pinch rollers?
Actions > Load extended lets you set a cutting area beyond them, but Summa says tracking isn't guaranteed in that mode.
My signs come out slightly too long or short. Is that tracking?
The S One feeds by friction, so length depends on media thickness. It's factory set for standard 2 mil cast or 3 mil calendered vinyl, and Summa states 0.2% accuracy on standard vinyl. For tighter matching between materials there is a length calibration under Calibrations; text us and we'll walk you through it.
Should I turn the media sensor off?
Leave it on unless we tell you otherwise. It finds the media and stops the cutter at the end of the roll, which protects the cutting strip and blade.
- Summa S One User Manual (Rev 001, distributor copy)
- AA support requests about Summa media loading and tracking, 2024 to 2026











































































