Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa S One OPOS print and cut: margins, OPOS origin, calibration and marks not read
Print the job with its OPOS marks, leaving 2 cm (0.8 in) at the sides and front of a roll and at least 40 mm after the last mark. Keep the cut line just inside or outside the artwork. If cuts land off the print, run Calibrate OPOS on black vinyl with white backing, and repeat it after every knife change. If the sensor won't find marks on glossy or unusual media, run Calibrate media (OPOS) with a printed 4 x 4 cm square.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Cut shifted the same way on every piece | OPOS needs calibrating | Step 5 |
| Marks not found, sensor error | Media or mark color hard to read | Step 6 |
| Drift grows on long jobs | No panelling | Step 4 |
| Cut nicks the print edge | Cut line on the artwork edge | Step 1 |
| Cutter starts reading in the wrong place | OPOS origin setting | Step 3 |
Step by step
-
Prepare the cut line
Draw the contour cut line, in the spot color your software expects. Don't place it exactly on the edge of the graphic, or the slightest media movement shows. Put it just inside, just outside, or inside a thick border you add around the design.
-
Print with proper margins
Print from software that supports print and cut, and laminate afterward if needed. On a roll, leave 2 cm (0.8 in) at the sides and front; short jobs can go down to 1 cm (0.4 in). On a sheet, leave at least 40 mm of media after the last mark, which is also the minimum to leave at the end of a roll. Choose OPOS X, XY, XY2 or Xtra in the software.
-
Load and start the job
Load the media straight with the pinch rollers set correctly, and send the job. With the default OPOS origin setting (Mark), the cutter asks you to move the tool over the first mark and confirm, then it searches around that spot. To skip that, change it under Configuration > OPOS parameters > OPOS origin: Current position searches from wherever you left the tool when loading; for OPOS XY jobs, XY line and Media centre let the cutter find the XY line and follow it to the first mark.
-
Long jobs: turn on panelling
Reading every mark before cutting means a lot of back-and-forth feeding, which hurts tracking. Under Configuration > OPOS parameters > OPOS panelling, choose On with 2 or 4 marks. Panels then follow the spacing of the marks. 4 marks re-reads the end of the previous panel for a better join. Use the cutter's panelling or the software's, not both.
-
Cuts off the print: calibrate OPOS
Load black vinyl with white backing (Summa requires this combination), then go to Calibrations > Calibrate OPOS. The cutter cuts a square of about 9.5 x 9.5 mm and feeds it forward. Weed it carefully so the edges stay intact and confirm. The sensor reads the edges and calibrates itself. Repeat after every knife change.
-
Marks not read: calibrate the media
Print a square of at least 4 x 4 cm on the job media, with the same ink as the marks. Load it and open Calibrations > Calibrate media (OPOS), then Measure. Follow the prompts to move the tool over a white area and then a printed area, confirming each time; the cutter makes a small circle as it measures. It then shows a value for that media and mark color. Write it down, so next time you can enter it with Set. An error means it couldn't tell the two apart, so check the test. If reading doesn't improve, tap Reset to default.
Still missing marks?
Text us at (562) 609-4996 with photos of the printed marks and a miscut piece, plus your RIP and media.
Watch Summa's video: print and cut with GoSign on the S1
More videos
Embedded from the manufacturer's official channel.
Common questions
Do I have to put the tool over the first mark on every job?
Not always. The OPOS origin setting under Configuration > OPOS parameters can start the search for you. Mark is the default and asks you each time. Current position starts searching right away from where you left the tool. With OPOS XY jobs, XY line and Media centre make the cutter find the XY line itself.
Long jobs drift by the end. What helps?
Turn on OPOS panelling in Configuration > OPOS parameters, with 2 or 4 marks. With 4 marks the cutter re-reads the last marks of the previous panel, which joins panels better. Don't use the software's panelling at the same time.
How far apart should repeated copies be?
At least 30 mm between copies on the same roll.
Media calibration didn't help. Now what?
Set the value back with Reset to default, as Summa advises, and text us a photo of the marks and media.
Can it run a whole roll without me?
Yes, with OPOS barcode. It needs software that prints the barcode, a barcode server program on the computer, and the barcode option activated with a code from Summa's product registration.
- Summa S One User Manual (Rev 001, distributor copy)
- Summa software and firmware downloads
- AA support requests about Summa contour cutting, 2024 to 2026











































































