Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex V-1000 and V-2000HD off contact, pallet leveling and micro registration
Vastex presses register well only when every screen is parallel to every pallet with about 1/8 in (3 mm) of off contact. Level one pallet and one head first, then use that same screen to set every other pallet, and finally level the remaining heads to the pallets. Loosen the locking knobs or levers before you turn any adjuster and retighten them before printing.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Off on some pallets | Pallets not set to the same screen | Pallets |
| Heavy on one side | Screen not parallel to pallet | Heads |
| Smear or double image | No off contact | Off contact |
| Micro knobs stuck | Clamp levers still tight | Micro registration |
Use your flattest aluminum screen for all of this. A warped frame gives false readings.
V-1000
-
Level pallet #1
Tighten the pallet arm knob. Read a level on the bottom of the pallet arm, then make the pallet top match that reading on both sides using the pallet adjusting nuts. Check the wheel lock housings are level with each other first (see the assembly guide), then match the pallet to a level reading across the wheel lock housing in the other direction. Before tightening, center the four leveling bolts in their slots. Mark this pallet #1.
-
Rough set head #1
Clamp a screen in head #1, lower it onto the bearings and set it about 3/8 in (10 mm) off the pallet. That's deliberately high.
-
Front to back
Loosen the front/rear pitch bolts half a turn, turn the front/rear pitch knob until the screen is parallel front to back, and retighten.
-
Side to side
Loosen the off contact and left/right pitch locking bolts on the front of the screen clamp half a turn. Turn the off contact/pitch screws one at a time until the screen is parallel side to side. Press down on the head to lower it. Tighten and recheck both directions.
-
Set 1/8 in
Loosen the same locking bolts and use both off contact screws to bring the screen down to 1/8 in (3 mm). Tighten.
-
Set the other pallets
Slide the screen in its clamp so its edge lines up with the pallet edge. Swing that head over each other pallet without touching the screen, and adjust each pallet's leveling bolts until it sits 1/8 in under the screen with its side lined up.
-
Level the other heads
Repeat steps 2 to 5 for every other head over any pallet.
For micro registration on the V-1000, loosen the micro locking knobs a quarter turn, then use the red side knob to move the screen side to side and the left and right micro knobs to rotate it or move it front to back. Retighten before you check off contact.
V-2000HD
Head #1 and the pallets are set at the factory. If you install screens in the rear clamps, line the inside of the frame up with the front of the clamp bar.
-
Lock everything first
Lower the head with the screen clamped. Make sure both micro clamp levers, both off contact locking levers and the pitch lock screw are tight.
-
Side to side and height
If a corner touches, loosen one off contact locking lever slightly and turn that side's off contact knob. Do one side at a time until the screen is level and about 1/8 in off the pallet.
-
Front to back
Loosen the pitch lock screw and turn the pitch knob: clockwise lifts the front, counterclockwise lowers it. Recheck side to side, then tighten all four levers and the lock screw without overtightening.
-
Pallets, only if needed
With a flat screen in head #1 and the gas spring set so the head stays down, check 1/8 in at all four corners of pallet #1. Swing head #1 over each other pallet, keep the pallet nuts finger tight, line the pallet side up with the screen and adjust the nuts at the bottom of the leveling bolts to 1/8 in. Then tighten.
V-2000HD micro registration
Loosen both micro clamp levers 1/4 to 1/2 turn (head down). Turn the X knob clockwise to move the screen right, counterclockwise for left. Turn both Y knobs clockwise to bring the screen toward you, counterclockwise to push it away, or just one to rotate it. Retighten the levers and check. Return to the centering sites at the start of each job.
V-100
Loosen the thumb screw slightly to set height and left to right angle, one side at a time, and the two head bolts to set front to back angle. If registration still drifts after all this, text us a photo of a test print at (562) 609-4996.
Watch Vastex's video: V-1000 head and pallet leveling
More videos
Embedded from the manufacturer's official channel.
Common questions
How much off contact should I use?
Vastex sets the screen about 1/8 in (3 mm) above the pallet. On the V-1000 the floating heads need off contact to register repeatably.
Should I level the press to the floor?
It doesn't matter much. What matters is that pallets and screens are parallel to each other and centered over the rotor arms.
My V-2000HD screen won't move when I turn the micro knobs.
Loosen the two micro clamp levers 1/4 to 1/2 turn first. The levers only loosen or tighten with the head down.
How fine is the V-2000HD micro adjustment?
One notch on a micro knob is about 0.0075 in and one full turn is 1/16 in. There's 1/2 in of travel in each direction, so start every job with the centering sites lined up.
Do I adjust the pallet or the head?
Once your pallets are set, adjust heads to pallets. When you set pallets, move the pallet to the screen, never the screen to the pallet.










































































