Support
Machine type
Brand
Vastex V-100, V-1000 and V-2000HD Manual Screen Printing Presses

Vastex V-1000 and V-2000HD lubrication, cleaning and detent adjustment

✓ Reviewed by Jason KimUpdated 2 min readFits: V-1000 · V-2000HD
Short answer

Once a month, put about 1/2 oz of light machine oil on the center hub bearings and a dab of grease on the head pivots, knob threads and spring holes. Clean lint and adhesive off the press every day or between jobs, and inspect it monthly while you lubricate. If the pallets don't stop firmly under the flash, adjust the rotor detent.

Vastex ships the V-1000 with a small bottle of oil and a tube of grease. Using them monthly prevents most premature wear on knobs, pivots and bearings.

When you clean or lubricate, make sure nobody is close enough to move any part of the press unexpectedly. Don't remove lift springs unless Vastex tells you to.

Monthly lubrication: V-1000

  1. Center bearings

    Find the bearing plate at the top center of the press. Squirt about 1/4 oz of light machine oil along the edge of the bearing, spin both hubs, add the other 1/4 oz and spin both hubs again. The oil runs down to all four bearings.

  2. Grease points

    Put a dab of grease on both sides of each print head pivot pin, on all adjustment bolt and knob threads, and in the lift spring mounting holes.

Monthly lubrication: V-2000HD

  1. Oil

    Several drops of light machine oil on both sides of each extension arm hinge, and about 1/2 oz on the center hub bearings.

  2. Thread lubricant

    Brush a small dab of white lithium grease or anti-seize on the threads, and a thin layer on the wear plates, of: the gas spring pins, micro adjustment locking levers, off contact locking levers, off contact knobs, X and Y micro knobs, front/rear pitch knob and lock screw, screen clamping knobs, and the pallet corner clamping knob threads and contact point. Remove knobs and levers if you need to reach them.

Daily cleaning

  • Clean the press every day or between jobs, especially lint around moving parts and adjusters.
  • Any solvent is fine on the pallet tops. Use a glass or multi-surface cleaner on painted parts and mineral spirits for spilled ink.
  • On the V-2000HD, keep spray adhesive off the gas springs.
  • Apply pallet tack only to an area slightly larger than the design. Tack near the edges lifts the rubber corners, worse on heated pallets. Liquid adhesive or double sided pallet tape cleans up more easily.

Monthly inspection

While you lubricate, look for anything worn, loose or out of place. Finding it early is cheaper than downtime. If a part breaks or the press doesn't behave normally, stop using it and contact us.

Adjusting the detent

The detent gives a repeatable stopping point for each pallet, for example under your flash. You can set it firm, loose or off.

Press How to adjust
V-1000 Loosen the lock nut (9/16 in). Turn the screw out for more holding pressure, in for less. Retighten.
V-2000HD after Jan 1, 2012 Same as the V-1000. A second spring may be inside the detent; fit it for a firmer stop or if one breaks.
V-2000HD before 2012 Loosen the nut with two 9/16 in wrenches and move the wheel up to increase or down to decrease holding pressure.

Watch Vastex's pallet adhesive overview

Embedded from the manufacturer's official channel.

Common questions

What oil and grease does Vastex use?

Light machine oil (SAE 20 or equal) for the center bearings and white lithium grease or anti-seize for threads and wear plates. Vastex sells a hardware lube kit with oil, grease and a brush.

What can I clean the pallets with?

Vastex says any solvent can be used on the pallet tops. Use a glass or multi-surface cleaner on painted surfaces and mineral spirits for spilled ink.

Oil is seeping from under the bottom bearing. Is that bad?

No. Vastex says that can happen over time. Wipe it off as needed.

The pallets don't lock in place under my flash.

Tighten the detent. On V-1000 and newer V-2000HD presses, loosen the lock nut and turn the adjuster screw out for more holding pressure. You can also add the second spring.

Why are my pallet rubber corners lifting?

Adhesive near the edges, especially on heated pallets. Only tack an area slightly larger than the design.

Did this fix it?