Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex V-100 assembly: stand, detents, hubs, rotor arms, pallets and print heads
Build the V-100 base and braces, drop in the two detents with two springs each, bolt up the rotor hub and C hub, then seat the bearings and tighten the top hub bolt only until the hubs spin with a little drag. Bolt on the rotor arms and pallets, assemble and hang the print heads with their springs and stop bar, then level each screen and line every pallet up to the first screen.
The V-100 comes as a 1-station, 1-color press (about 65 lb) or a 4-station, 4-color press (about 132 lb). Many bolts go in loose first and are tightened later, so follow the order. Assemble it with two people.
Base and detents
-
Base
Line up the notches, fit four 5/16 in bolts and lock nuts and leave them loose. Wiggle the shaft into the base (it's a very tight fit), then fit and tighten the 1/2 in bolt and lock washer with a 3/4 in wrench. Now tighten the four loose bolts with a 1/2 in wrench and bolt on the two stand braces.
-
Detents
Insert the tab of each detent into the slot in the base and rotate it into position. Fit two springs per detent.
Hubs
-
Rotor hub
Fit the long 5/16 in bolts and lock nuts loosely. On a 1-station press tighten three sets; on a 4-station press leave all outer bolts loose. Then tighten all the inside bolts.
-
C hub
Fit the hinges to the C hub with the 2-1/4 in bolts, loose. Install all your hinges now.
-
Bearings and center bolt
The bearings only fit one way and must sit in the race in each hub. Fit the large washers and the top 1/2 in bolt and tighten it with a 3/4 in wrench only until there is light drag when you spin each hub on its own. If the press won't spin easily, back the bolt off in 1/8 turn steps. Then tighten the hinge bolts.
Rotor arms and pallets
-
Rotor arms
Remove two nuts per arm from the rotor hub, drop the arm's tabs into the slots in the bottom hub plate, and fit the lock nuts and bolts. Repeat for each arm, then tighten every remaining lock nut.
-
Pallets
Build each pallet arm (bolts, T weld nut, knob, corner clamp bracket and clip), then bolt the arm to the pallet centered on its slots. Sleeve, tagless and mask pallets mount slightly differently; follow step 7 of the manual for those.
-
Fit pallets
Slide each pallet and arm onto its rotor arm. Use the slots on the side of the rotor arm to set every pallet in the same place, and tighten the knob without overtightening.
Print heads
-
Build the head
Fit the off contact brackets with the thumb screw, bolt on the screen clamp mount with the double nuts, assemble the screen clamp (knobs, clip nuts, washers, screws, retainer clips and pods) and bolt it to the head with carriage bolts.
-
Hang and spring it
Hang the head on its hinge and attach the springs. The manual shows three spring positions: Normal, Heavy and Extra Heavy, for heavier screens.
-
Stop bar
Fit the stop bar with the head in the down position. Don't print without it.
Level and align
Clamp a flat screen. Loosen the thumb screw slightly to set screen height and left to right angle, one side at a time. Loosen the two head bolts slightly to set front to back angle. On the 4-station press, slide the leveled screen so its edge lines up with the pallet edge, then lower it over each other pallet without touching the screen. If a pallet is off, loosen its pallet arm nuts, line its side up with the screen and retighten. Stuck on a step? Text us a photo at (562) 609-4996.
Common questions
What tools do I need?
1/2, 5/16 and 3/4 in wrenches (or 8, 13 and 19 mm), plus an adjustable wrench for the center bolt.
The press is hard to turn. What's wrong?
The top hub bolt is probably too tight. Loosen it in 1/8 turn steps until each hub spins with light drag.
Can I add colors later?
Yes. The V-100 is expandable from 1 by 1 to 4 by 4. Vastex sells additional print heads and V-100 build-a-press parts, and most V-1000 pallets fit the V-100.
How do I set the screen level?
Loosen the thumb screw to set height and left to right angle, one side at a time. Loosen the two bolts on the head to set the front to back angle.
- Vastex V-100 Assembly Manual, doc 01-26-001F (PDF)
- AA support requests about Vastex presses, 2024 to 2026











































































