Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex V-2000HD assembly: uncrating, wheels, rotor arms, gas springs and print heads
The V-2000HD arrives mostly built, with pallets already leveled at the factory and print head #1 already set. Slide it off the skid, add wheels or a service pan if you bought them, bolt each numbered rotor arm into its matching position, fit the gas springs barrel up, and hang the print heads on their mounting bolts. Then set the remaining heads to 1/8 in off contact using head #1 as the reference.
The V-2000HD is shipped on a skid with the rotor arms packed separately, each with its pallet already attached. Some accessories are packed with the press, so check every box before you throw packaging away.
Note any crate damage on the driver's ticket before you sign. If you find hidden damage later, report it to the trucking company right away and keep the packaging.
Step by step
-
Uncrate
Remove the straps, the top and sides of the crate and the shrink wrap. Take out the rotor arms and unpack the boxes under the press.
-
Get it off the skid
Remove the lag bolts at the feet and carefully slide the press onto the floor. If you bought wheels, slide two legs just to the edge of the skid and fit their casters first, then the rest one at a time.
-
Wheels and service pan (optional)
Standard casters bolt through the foot brace with a 1/2 in nut (3/4 in wrench). For the standard service pan, lay it on the floor, roll the press over it, line up the holes with the inside of the feet and bolt it with the flat washer under the pan. The drop down wheel set and split service pan go together as shown in the manual; leave two opposite caster assemblies off until the pan halves are in.
-
Rotor arms
Put each arm in its numbered position. Two hooks hold the arm while you fit four gold washers and four 3/8 in bolts. Tighten these very well. If you want less upward play, push the pallet down firmly, drill through the pilot hole with a 3/16 in bit and tap in the supplied roll pin on both sides.
-
Gas springs
The gas springs are in the print head box. Fit them barrel up, using the slots the manual shows to start. There are four slots per side; move them later to change how the head feels.
-
Hang the print heads
Pull the head mounting bolts on each swivel arm forward, set the large holes in the head's back plate over the bolts and slide the head all the way down into the slots. Fully tighten only the locking levers on head #1, which was leveled at the factory to swivel and extension arm #1. The locking lever handle can be pulled out and rotated to a comfortable position.
-
Set the other heads
Clamp a flat screen in each remaining head and adjust it to 1/8 in off contact over the leveled pallets using the pitch and off contact knobs. If head #1 moved in shipping, adjust the head, not the pallet. See our off contact and pallet leveling guide for the exact knob order.
Pallet tack
Vastex warns against spraying pallet adhesive near the edges of the rubber tops, especially on heated pallets, because the corners lift. Only cover an area slightly bigger than your design, keep adhesive off the gas springs, and consider liquid adhesive or double sided pallet tape for easier cleanup.
If a head won't stay down or a gas spring feels weak, text us a short video at (562) 609-4996.
Watch Vastex's overview of the V-2000HD manual press
More videos
Embedded from the manufacturer's official channel.
Common questions
Do I need to level the pallets on a new V-2000HD?
Usually not. Vastex has preassembled and leveled the pallets at the factory since summer 2010, and head #1 is factory set. Adjust the heads to the pallets rather than the other way round.
Which gas spring slots should I use?
Start with the slots shown in the manual, barrel up. You can move the spring to any of the four slots per side to get the feel you like.
The rotor arm lifts slightly when I pull up on it. Is that a problem?
No. The press is designed for downward pressure. If the movement bothers you, Vastex supplies a roll pin you can fit through the pilot hole for extra rigidity.
How heavy is it?
From about 400 lb (V2HD-44) to about 1,075 lb (V2HD-1010). Use enough people to move it safely.
The crate was damaged. What should I do?
Note it on the driver's delivery receipt before you sign. If you find hidden damage, report it to the carrier right away and keep the packaging, then contact us.
- Vastex V-2000HD Assembly, Operating and Maintenance Instructions, doc 01-08-043I (PDF)
- AA support requests about Vastex presses, 2024 to 2026










































































