Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vega S17 setup and first print: site, power-on order, first ink charge and media setup
Before the Vega S17 arrives, have a spot with about 39 inches of clearance, 59 to 77°F and 45 to 70% humidity, and the circuits we confirm with you. Turn on the finishing section first, then the print section. The first ink charge takes about 20 minutes: don't open the top cover or pull a cartridge until the screen says Ready. Then run Media Set Up, turn the heater on, and print a nozzle check before your first job.
Before it arrives
- Space: about 39 inches clear on every side and 4 inches above. The complete machine is about 67 by 31.4 inches and weighs about 626 lb. At 31.4 inches deep it passes a standard doorway.
- Room: 59 to 77°F and 45 to 70% humidity is the recommended range. Dry rooms cause nozzle dropout.
- Power: each section has its own cord. Confirm circuit requirements with us before installation.
- Network: wired Ethernet is the most reliable. If you connect both Ethernet and Wi-Fi, the machine uses Ethernet. Software updates need internet access.
Setup steps
-
Place the machine and set up the waste ink bottle
Lift the print section with four or more people, using the lifting indentations at the base. Never hold the film unwinder. For the waste ink bottle, put the tube into the bottle and close the cap with no gap. Connect the other end to the connector at the right rear of the print section and push until the marking on the tube disappears into the connector. Stand the bottle upright and keep the tube straight, running downhill from the machine to the bottle with no kinks or loops.
The machine can't tell whether the bottle is connected. A bottle on its side or a kinked tube can leak or clog.
-
Power on in the right order
Turn on the finishing section's main power first. Then turn on the print section's main power switch and hold the sub power button for more than 2 seconds.
-
Shake the white cartridges, then load all cartridges
White ink settles in the box. Before you insert a new white cartridge, hold it with the ink port facing up and shake it side to side at about 45 degrees, two shakes per second, for 50 seconds. Don't shake hard or drop it. Load two white cartridges, two cleaning cartridges, and C, M, Y and K into their marked slots, then check that the screen recognizes each one.
-
Let the first ink charge finish
The first ink charge takes about 20 minutes. Don't lift the top cover and don't pull out a cartridge while it runs. It's finished when Ready shows at the top left of the screen. If opening the cover paused it, hold the sub power button to restart and let it run again. If the charge fails, stop and contact us.
-
Load the adhesive powder cartridge
Install the powder cartridge in the finishing section. Depending on the machine's software version, the first powder fill is either automatic or a short manual step. We'll walk you through it at installation.
-
Set the clock and the cleaning schedule
Go to Settings > Option > Time Zone. It starts at UTC, and a wrong time zone makes scheduled maintenance run at the wrong time. Then set Settings > Option > Cleaning Schedule Set (up to three times a day or by date) so the machine does its maintenance when you're not printing.
-
Load film and run Media Set Up
Load the 17 inch film flat and centered. Trim the leading edge if it's wrinkled, torn, folded, curled or has tape or sticky residue on it. Open the status window by pulling down the status bar and press Media Set Up. You can't print until this has run.
Never start printing on film that isn't lying flat. Raised film can skew and hit the print heads.
-
Turn the heater on and print a nozzle check
Tap Heater on the main screen and wait until it turns green. Then go to Maintenance > Nozzle Check. Each block is labeled with a head number. Gaps in a block mean a clogged nozzle, and wavy lines mean deflection. Clean only the head that needs it: see our daily maintenance guide. Take a photo of the pattern. We'll ask for it if you contact us.
-
Send your first job
Send the job from your RIP, or press USB to pick a .prn file from a USB drive, or Stored to reprint one of the last 20 jobs. Press Print. With the finishing section attached, sheets are cut, powdered, cured and stacked automatically. The stacker holds 100 sheets.
Check before you call it done
- The status light on the machine is green, not purple or red.
- Every cartridge shows a percentage, with no X or NC.
- The waste bottle is upright with a straight tube.
- The nozzle check is complete on the CMYK heads.
Something not right? Text us a photo or short video at (562) 609-4996.
Common questions
Can I switch the machine off at night?
No. Leave it on. It runs its own cleaning and white ink circulation on a schedule, and being off for 12 hours or more can clog the heads.
Which section do I turn on first?
The finishing section first, then the print section. Never switch the finishing section on while a job is printing.
Why did roll-to-roll and cutter settings lock themselves?
That's by design. With the finishing section attached, the machine runs roll in, cut sheets out, so the cutter and feed options stay on.
Does it plug into a regular outlet?
Each section has its own power cord. Confirm circuit requirements with us before installation.
How many people does it take to move?
The print section alone weighs about 243 lb. Lift it with four or more people using the lifting points at the base, and never lift by the film unwinder.
- DTF Station technical documentation
- AA support requests about DTF printer installation and first prints, 2024 to 2026











































































