Support
Machine type
Brand
DTF Station Vega S17

Vega S17 warnings and errors: status light colors, ink and waste messages, sheet jams 211 to 261

✓ Reviewed by Jason KimUpdated 3 min readFits: Vega S17
Short answer

Check the status light first. Green means fine, purple means a warning to read in the status window, blue means busy, and red means printing and automatic cleaning have stopped, so deal with it right away. Low ink, empty cartridges and a full waste bottle all stop the automatic cleaning. A 2xx warning number means a sheet stopped in the finishing section: remove it and press the resume button shown. Any SC message means call us.

Start with the status light

Light What it means What to do
Green Working normally Nothing
Blue Busy printing or cleaning Wait
Purple Working, but there is a warning Pull down the status bar and read the status window
Red Error. Printing and automatic cleaning have stopped. Fix it today. Left overnight, the heads can clog.

Messages that stop automatic cleaning

The machine skips its own cleaning while any of these is true: it's switched off, a cartridge is missing or at 0%, the waste bottle is full, there's an encoder error or any other error, an SC message is showing, the top cover is open, or the ink bay is open.

Message What to do
Low ink Replace the cartridge soon. Keep every cartridge above 5%: the cleaning cycles need it. White below 1% can't print. If you don't have ink, put in a cleaning cartridge rather than leave a slot empty overnight.
Ink empty Replace the cartridge now, then print a nozzle check.
Waste ink bottle almost full or full Empty the bottle, put it back upright with the tube straight, then press Waste Ink Reset. Never reset without emptying: the counter is the only way the machine knows, and the bottle will overflow.
Cartridge shows X or NC No cartridge detected. Reseat it. Wipe the cartridge port and slot with a dry lint-free wipe first (no cleaning liquid near the slot's circuit board).
Encoder error Contact us. The encoder strip isn't something you can clean yourself, and repeated encoder errors need our guidance.
SC followed by a number A service call. Write down the number and contact us as soon as possible. Automatic cleaning is stopped until it's cleared.

Finishing section warning numbers

A warning number in the 200s means a sheet didn't reach the next sensor in time. The middle digit tells you where along the path it stopped.

Warning Meaning To resume
211 No sheet at sensor 1 Remove the sheet near sensor 1, press [1-1]
212 Sheet longer than expected at sensor 1 Nothing to clear. The job continues. Check your cut length.
221 No sheet at sensor 2 Remove the sheet near sensor 2, press [1-2]
231 No sheet at sensor 3 Remove the sheet near sensor 3, press [2-1]
243 or 253 Powder paddle sensor 1 or 2 timed out Remove the sheet, press [2-2] or [3-1]. The heater bed keeps feeding meanwhile.
261 No sheet at sensor 6 Remove the sheet near sensor 6, press [4-1]

If the same number keeps coming back at the same spot, check that no printed sheet is left in the film path, and that the heater bed and media guide are clean (see our maintenance guide). Then contact us.

Other things that look like faults

  • The finishing section won't start and nothing is jammed: a door or cover isn't fully closed. Close every door firmly.
  • The print section doesn't see the finishing section, or it acts strangely after a power cut: shut both down, then power on the finishing section first and the print section second. Never switch the finishing section on mid-print.
  • The cutter and sheet mode turned themselves on: that's normal with the finishing section attached.
  • The carriage travels the full width even on narrow jobs: turn on Settings > Option > High Speed Mode. It's faster but slightly lower quality.

Print quality problems

What you see Try this, in order
Thin horizontal lines across the print Clean until the CMYK nozzle check is complete. If it already is, run Alignment > Head Alignment.
Thick bands in dark or gray solids, nozzles complete Print in one direction only (uni-directional), or use a higher quality print mode.
Fuzzy or blurry prints Check your RIP's rendering intent (perceptual) and profile, then clean any wavy nozzles, then run Head Alignment.
Color shifted from the white underbase Alignment > Print Position > White to Color, then Head Alignment if needed.
Dull colors, nozzles complete Check the output profile in your RIP matches the print mode.
White lines through every color block after a manual clean Stop printing and contact us.

When you contact us, have the light color, the full message, and a nozzle check photo ready. Your serial number and software versions are under Settings > Information. Text us a photo or short video at (562) 609-4996.

Common questions

Why does a dismissed message keep coming back?

Ink and waste bottle messages come back every 12 hours, and the "auto maintenance can't run" message comes back every 5 minutes, until the cause is fixed.

A cartridge suddenly reads 0% but was over half full. Is it empty?

Probably not. Pull it out until the screen shows NC, then push it back in. If it still reads 0%, power the machine off and back on.

My white looks dull but the nozzle check is fine. Why?

The white ink has settled. Shake the white cartridges for 2 minutes, then run 3 to 4 Strong cleanings on the white heads.

After the first fill several nozzles won't come back no matter how much I clean. What now?

Air can get into a head during the first fill or a manual clean. Let the machine sit overnight and check again.

Warning 212 keeps showing. Is something stuck?

No. 212 means the sheet is longer than the machine expected and the job keeps going. Check the cut length in your job settings.

Sources
  • DTF Station technical documentation
  • AA support requests about DTF printer errors, 2024 to 2026
Did this fix it?