Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Viper MAXX light or heavy bands in the spray: tip wear, tip gauge and step setting
The MAXX sprays in side-to-side passes, stepping back between each one, so a worn, dirty or crooked tip shows up as light or heavy bands. Clean the tip with a soft toothbrush and cleaning solution, and if bands remain, replace it and align it with the tip gauge Viper supplies. Then fine-tune the Y-Axis Steps Between Spray setting: a lower number overlaps the passes more and fixes light bands, a higher number fixes heavy bands.
Match your symptom
| What you see on the shirt | Most likely cause | Go to |
|---|---|---|
| Light stripes between passes | Passes not overlapping enough, often a worn or misaligned tip | Steps 1 to 5 |
| Heavy stripes where passes overlap | Too much overlap for your tip | Step 4 |
| Patchy, irregular pattern | Dried pretreat on the tip, or a damaged tip | Steps 1 and 2 |
| More pretreat than usual at the same setting | Worn (eroded) tip | Step 2 |
Why tips cause bands
Viper lists five ways a spray tip goes bad: erosion (the opening wears larger and puts down more), corrosion from harsh pretreats, caking or bearding (dried pretreat at the opening, often invisible), accidental damage from hard tools or drops, and clogging from polymers that separate out of the pretreat. Any of them changes the width or evenness of each pass, and because the MAXX lays passes side by side, the error shows up as bands.
Step by step
-
Bring the tip to the front
From the main screen press Utilities, then Spray Tip Replacement. The gantry moves to the front of the machine so you can reach the tip. Then switch off and disconnect the power before you reach in.
-
Clean it, or replace it if it's worn
Clean the tip with a soft bristle toothbrush and cleaning solution, then rinse it with water. Never use a pin or needle, and don't drop it. If a clean tip still bands, or puts down noticeably more than it used to, fit a new one. Viper's video on removing, replacing and aligning spray tips shows the full procedure.
-
Align the tip with the gauge
Use the tip gauge from the MAXX accessory box to set the new tip straight to the platen, as shown in Viper's video. A crooked tip gives an uneven band edge on every pass.
-
Match the steps to the tip
The Y-Axis Steps Between Spray value sets how far the gantry moves back after each pass. From the factory it's set so passes barely overlap. If you see lighter bands, lower the number for more overlap. If you see heavier bands, raise it. Viper rates one inch at about 618 steps, so change it a little at a time. Viper's video on steps shows where to find the setting on your version.
-
Re-weigh
Changing the tip or the steps changes how much pretreat lands on the shirt. Viper says to re-test and weigh a shirt for your laydown values after any change, or rerun the step test from our MAXX step test guide.
Keep the tip from drying
With Auto Clean on, the MAXX briefly fires the spray head and pump after it has sat idle for the time you set, to keep the tip wet. Viper suggests 20 to 30 minutes in dry climates. Purge the pretreat out and leave only water in the machine at the end of every day, and keep the bellows and lids in place so pretreat mist doesn't build up on the mechanics.
Viper says the spray head minimum and maximum speeds and the spray offsets generally should not be changed. If the bands don't go away after a new, aligned tip and a step adjustment, text us a photo of the sprayed shirt at (562) 609-4996.
Watch Viper's video: how steps affect your spray pattern and how to adjust them
Embedded from the manufacturer's official channel.
Common questions
Why does my MAXX put down more pretreat than it used to?
Viper explains that spray tips erode over time, enlarging the opening, so a worn tip lays down more than a new one at the same setting. Re-weigh shirts and replace the tip when the pattern goes irregular.
What can I clean the tip with?
Only a soft bristle toothbrush and cleaning solution, then rinse with water. Viper warns that hard tools scratch the tip and that dropping it can damage it.
Where is the tip gauge?
It's in the MAXX accessory box. Viper's video shows how to remove the tip, fit a new one and use the gauge to align it to the platen.
How much does one step move?
Viper rates the MAXX at about 618 steps per inch of gantry travel, so change the value in small amounts and check the pattern each time.
I changed several settings and now it sprays badly. Can I undo it?
Viper's advanced menu has a Restore All Factory Defaults option. Text us at (562) 609-4996 before you use it so we can check your version first.











































































