Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Viper MAXX spray step test and bar code presets: find the right pretreat amount
On MAXX firmware HMI5001 PLC3020 or newer, go to Utilities, then Spray Test. The MAXX sprays six columns on one shirt, from about 11 g up to about 35 g by default. Cure it, print a solid white bar across all six, and pick the column where the white stops getting more opaque. Older firmware can run the same test from Viper's bar code sheet, and a bar code scanner can also load a spray amount and area for each shirt style.
The right amount of pretreat changes with every shirt style, color and pretreat dilution. The MAXX's step test lets you find it on one shirt instead of guessing across a stack.
Run the built-in step test
You need firmware HMI5001 PLC3020 or newer. The version is shown at the bottom left of the main screen.
-
Open the step test
From the main screen press Utilities, then Spray Test. You'll see six steps, each with its own laydown value, plus a spray length you can set to any length.
-
Check the values
Viper's defaults run from about 11 g to about 35 g in roughly 5 g jumps:
Step Setting About 1 0 11 g 2 33 15 g 3 52 20 g 4 68 25 g 5 78 30 g 6 84 35 g To zero in on a narrower range, tap a value and type a new one. Viper's example for 11 to 21 g in 2 g steps uses 0, 20, 33, 42, 50 and 58.
-
Spray, cure and print
Load the shirt, run the test and cure the pretreat as you normally would. Then print a solid white box across all six columns with your usual print settings. Viper leaves a small gap between columns so you can tell them apart.
-
Read the result
Look for the point where the white stops getting more opaque. If two neighbouring columns look the same, the lower one is your amount, or a setting between them. Remember that step 1 is on the right side of the platen, but reads left to right when you hold the shirt up as worn.
-
Save it as a preset
Store that laydown value against the shirt style. The MAXX has four quick-select presets on the main screen and 30 custom presets (0 to 30) you can edit in Utilities. Save your settings before you go back to the home or previous screen.
Older firmware: use the bar code step test
Viper publishes a printable step test sheet with a bar code for each step. Load the shirt, scan step 1, then press Start or scan the sheet's Scan to Spray code. Mark the edge of each band with a silver marker, then repeat for steps 2 to 6. Cure, print a white bar across the platen width (15 to 16 inches) and read it the same way. Viper's sheet runs from about 11 g to 22 g (0, 20, 35, 46, 53 and 60% laydown).
Load presets by bar code
A scanner (or a data string sent over the USB cable) can set the spray amount, the area, or both. Each code ends with a carriage return, which most scanners add automatically. Viper's formats:
| To set | Format | Viper's example |
|---|---|---|
| Amount and area | 24 digits, in groups of 4: laydown % without the decimal, width, height, auto-center (0000 off, 0001 on), X start, Y start. Sizes in hundredths of an inch. | 555014501500000005500600 (55.50% laydown, 14.5 x 15 inches, not centered, starting 5.5 and 6.0 inches in) |
| Amount only | S plus the laydown % as three digits (XX.X) | S330 (33.0%) |
| Area only | LOCA plus the same 20 area digits | LOCA06000600000013500000 (6 x 6 inch left chest) |
| Start spraying | GOGO | GOGO |
Viper's gram figures are approximate. Spray tips wear and put down more over time, so repeat the step test when you change tips, change pretreat, or start a new shirt style, and weigh a shirt now and then to check.
Watch Viper's video: changing the amount of pretreatment on the MAXX
Embedded from the manufacturer's official channel.
Common questions
I don't see a Spray Test icon. Why?
The built-in step test needs firmware HMI5001 PLC3020 or newer. The version shows at the bottom left of the main screen. On older firmware, use Viper's bar code step test sheet and a scanner instead.
Which column is step 1 when I look at the shirt?
On the platen, step 1 is on the right. When you hold the shirt up as if wearing it, steps 1 to 6 run left to right.
Two columns look the same. Which do I pick?
The lower one, or a setting between the two. If steps 4 and 5 look equally opaque, step 4 (or a value between 68 and 78) is your setting.
Can I narrow the test range?
Yes. Tap each step's value and type a new one. Viper's example for 11 to 21 g in 2 g steps uses 0, 20, 33, 42, 50 and 58.
Do I need special software for bar codes?
No. Any free bar code generator works. Viper links one from its step test sheet. The scanner just has to send a carriage return after the code, which most do automatically.
- Viper MAXX spray step test instructions (HMI5001 PLC3020)
- Viper MAXX advanced menu manual, HMI5001 PLC3020: utilities and step test
- Viper MAXX bar code scanning worksheet
- Viper MAXX bar code step test sheet
- Viper MAXX Quick Start Guide and Manual v4.1: presets
- Viper MAXX how-to and tech support page











































































