Support
Machine type
Brand
Viper MAXX pretreatment machine

Viper XPT-1000 or MAXX not spraying, spraying unevenly or not pulling pretreat

✓ Reviewed by Jason KimUpdated 3 min readFits: Viper XPT-1000 · Viper MAXX
Short answer

Most Viper spray problems are dried pretreat: in the spray tip, the spray head solenoid or the fluid solenoids. Start by checking that the supply tube is fully seated and its filter is under the liquid and clean, then clean the spray tip with a soft toothbrush and warm water. If the machine can't move any fluid at all, Viper's test is to bypass the fluid solenoids: if fluid pumps that way, clean the solenoids; if not, the pump and spray head need cleaning.

Match your symptom

What you see Most likely cause Go to
Hourglass-shaped spray pattern Supply tube not fully seated, or tube filter out of the liquid or dirty Step 1
Patchy, streaky or narrow spray Dried pretreat on or inside the spray tip, or a worn tip Steps 2 and 3
Spray head runs but little or nothing comes out Dried pretreat in the spray head solenoid Step 4
Can't pump pretreat, water or cleaner through at all Fluid solenoids or pump blocked Step 5
Grinding while traveling, or spray cutting on and off mid-pass (XPT-1000) Damaged wire inside the cable chain Last section

Before you open anything: on the XPT-1000 press the red E-stop, then unplug the power supply. On the MAXX, disconnect the power supply before cleaning.

Step by step

  1. Check the supply tubes and filters

    Push each supply tube firmly into its fitting. Make sure the tube feeding the spray is under the liquid, and wipe any debris off the filter on its end. On the MAXX, shake the pretreat jug before each day's use, then purge for 10 seconds to fill the line.

  2. Clean the spray tip

    With the power off, dip a soft-bristle toothbrush in clean warm water and brush the tip until it's visibly clean. Then purge a couple of times to clear any loosened residue. If it's badly caked, soak it in cleaning solution in the tip soaking jar that came with your machine, then rinse with water.

    Never poke the tip opening with a pin or wire. Viper lists scratches from improper tools as a cause of bad spray patterns.

  3. Replace a worn tip

    Tips wear from erosion and from corrosive pretreats, and the opening slowly grows. A worn tip sprays more pretreat and a less even fan, even when it's clean. On the MAXX, use the tip gauge when you fit the new tip (see the video above), then check your Steps so the spray passes meet without gaps.

  4. Clean the spray head solenoid

    Remove the black nut that holds the spray tip against the solenoid. With a 7/64 inch hex key, remove the 4 bolts that hold the solenoid together, keeping track of the O-ring, which can stick to the tip. Note how the piston and spring sit, then clean the piston, spring, plastic housing and the electromagnet housing until no hardened pretreat remains. Reassemble in reverse order. Viper notes this can be done with the solenoid still mounted.

  5. Can't move any fluid? Bypass the fluid solenoids

    This test is from Viper's support page for the XPT-1000. Connect an outside line of water straight to the inlet side of the pump at the union on the clear tube, about 3 to 4 inches from the pump. If fluid pumps through that way, the fluid solenoids are blocked: take them apart and clean the piston, spring, body and direction cup (Viper's solenoid PDF shows each part). If nothing pumps even then, the pump and spray head need to be taken apart and cleaned.

    Take a photo of where each tube goes before you disconnect anything. Viper's PDFs show the routing, and a swapped line won't spray.

Wiring and noise problems

On the XPT-1000, grinding during travel, or a spray head that switches on and off during a pass, points to the wires inside the cable chain. Viper's fix is to take the lid and bellows support off, open the chain at the ribs and look for a cracked or broken wire. That's a repair job: text us a photo or short video at (562) 609-4996 and we'll help you find the right part.

Stop it happening again

Flush daily. Viper says even hot tap water (not boiling) flushes pretreat out better than room-temperature water, and to use distilled water if your water is hard. See our Viper daily and weekly cleaning guide.

Watch Viper's video: changing the spray tip and using the tip gauge on the MAXX

Embedded from the manufacturer's official channel.

Common questions

Why does my spray pattern look like an hourglass?

Viper's first two checks are that the supply tubes are pushed fully into their fittings, and that the tube is under the liquid with no debris on its filter.

How often do spray tips wear out?

Viper treats tips as wear parts. Erosion and corrosive pretreats slowly enlarge the opening, which changes the pattern and puts down more pretreat than when the tip was new. Dried buildup, scratches from hard tools and drops do the same. If a clean tip still sprays badly, replace it.

What can I clean the tip with?

A soft-bristle toothbrush and warm water, or the cleaning solution Viper approves, then rinse with water. Never use pins, wire or anything hard in the opening.

The spray head turns on and off while spraying, or I hear grinding. Is that a clog?

Usually not. On the XPT-1000 Viper points to the wires inside the cable chain: a cracked or broken wire there needs repair or replacement. Text us a video at (562) 609-4996.

Do I need to take the tip off every day?

No. Viper says that if you do the daily flush, you only remove the tip when it isn't spraying evenly.

Did this fix it?