Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Viper XPT-1000 setup: unpacking, supply tubes, power, Speed and Length knobs, and spraying your first shirt
Set the spray base on a level table, remove the two left rubber feet from the spray unit and seat it on the base, push the three supply tubes into their inputs, then connect the 24 V power supply and twist the red E-STOP a quarter turn right to release it. The Speed knob sets the amount of pretreat (read it off the laydown chart on top of the spray unit) and the Length knob sets the spray length from 2 to 24 inches. Load the shirt collar toward you and tap, don't hold, the green Start button.
What's in the boxes
The XPT-1000 ships in two boxes: the spray unit and platen (about 50 lb) and the spray base (about 32 lb). Lift the spray unit from the bottom with two people and never by the spray bar. Viper's accessories box, inside the spray unit box, holds:
- Starter quarts of Image Armor Light, Dark and Ultra pretreatment, and a quart of Image Armor Cleaning Solution
- A tip soaking container with a toothbrush and a 3 mm hex key
- A purge bottle
- The 24 V power supply
- Three supply tubes with filters
Set it up
-
Place the base
Take the spray base out of its box and put it on a level table.
-
Mount the spray unit
Unscrew and remove the two left rubber feet from the spray unit, then set the unit onto the base. Viper's two setup videos show this step.
-
Connect the supply tubes
Firmly push each of the three fluid supply tubes into its input on the spray unit (pretreatment, cleaning and water) and put each filter end into its container.
-
Connect power
Plug the 24 V power supply into a 110 V outlet, then into the power jack on the rear right of the spray unit.
-
Release the E-STOP
Twist the red E-STOP a quarter turn to the right. Pressed in, it cuts all power and stops all motion.
The controls
| Control | What it does |
|---|---|
| Start | Starts a spray cycle. Press and release; don't hold it |
| E-STOP | Cuts all power and motion |
| Speed knob | Sets how much pretreat goes down, read in grams from the laydown chart on top of the spray unit |
| Length knob | Sets the spray length shown on the dial, 2 to 24 inches |
| Rear buttons | Green CLEANING, blue WATER and red PRETREATMENT run each fluid line, used for flushing and daily cleaning |
The XPT-1000 sets the amount by how fast the spray head moves, which is what the Speed knob controls. Viper's chart values are approximate, usually within 2 grams, and change with spray head height. Weigh a test shirt before and after spraying to confirm. See how much pretreat to use.
Spray your first shirt
-
Make sure pretreat reaches the nozzle
Viper's manual uses the red PRETREATMENT button on the back to push fluid through the pretreatment line. With the purge bottle under the nozzle, press it until pretreat comes out of the nozzle.
-
Load the shirt
Drape it over the platen with the collar closest to you. Pull it toward you so the fabric is smooth, and keep the sleeves off the platen and out of the spray area. Use the line laser to find the center of the spray pattern. You can stack several shirts on the platen to speed up production.
-
Set Speed and Length
Pick the grams you want from the laydown chart and turn the Speed knob to match. Set the Length knob to cover the print area.
-
Spray
Press and release the green Start button. A cycle takes about 4 to 10 seconds depending on the laydown setting.
-
Cure
Remove the shirt carefully and cure the pretreat as your pretreat maker specifies.
Always test your settings before you sell a finished garment. Viper's chart is a starting point, not a guarantee.
Flush with the cleaning and water buttons at the end of every day. Viper's full routine is in Viper daily and weekly cleaning.
If it won't spray or won't pull pretreat, see Viper not spraying. If the laser doesn't come on, or your unit has fewer supply inputs than described here, Text us a photo or short video at (562) 609-4996.
Watch Viper: XPT-1000 setup
More videos
Embedded from the manufacturer's official channel.
Common questions
How much pretreat does the XPT-1000 put down?
Viper rates it at 5 to 60 grams over a 14 x 14 inch area, set by the Speed knob and read from the laydown chart on top of the spray unit. Values are approximate, within about 2 grams, and they also change with spray head height.
How big an area can it spray?
Up to 20 inches wide by 24 inches long. The spray length is adjustable from 2 to 24 inches.
Nothing happens when I press Start.
Check the red E-STOP. Pressed in, it cuts all power. Twist it a quarter turn to the right to release it. Also check the 24 V supply is plugged into the rear right power jack.
Can I hold the Start button down?
No. Viper says to press and release it quickly.
How do I pretreat a hoodie?
Lay the hood over the front vertical panel of the spray base and slide the spray head left or right to center the pattern on the garment.
- Viper XPT-1000 User Manual, Rev 1.0
- Viper XPT-1000 video series
- Viper tech support page
- AA support requests about the Viper XPT-1000, 2024 to 2026











































































