Support
Machine type
Brand
xTool F2 Ultra UV

xTool F2 Ultra UV error messages and fixes: not turning on, access-control key, flame detected, device moved, exhaust fan

✓ Reviewed by Jason KimUpdated 2 min readFits: F2 Ultra UV (MXF-K007-001 · MXF-K007-002 · MXF-K007-003)
Short answer

Most F2 Ultra UV errors have a quick fix. If it won't turn on, the usual cause is a pressed emergency stop: twist it to release, and check the power adapter light. "Access-control key" means reseat the key or try the spare. "Device moved" means put it on a level, steady surface and update firmware. "Exhaust fan installation abnormal" means reseat the fan module with the power off. "Flame detected" means check for fire first; if none, it's usually reflection.

Match your message

Message or symptom First thing to try
Won't turn on Release the emergency stop; check the adapter light
Access-control key Update firmware; reseat the key; try the spare
Flame detected Check for fire; then stop reflections
Device moved Level, steady surface; update firmware
Exhaust fan installation abnormal Power off and reseat the fan module
Auto-focus failed Placement, material, connection, calibration
Faint marks on wood Restart; overlap the spots; test on basswood

Won't turn on

Signs: you press the power button and nothing happens, the XTOOL logo stays dark, and no red or blue spots show on the baseplate.

  1. Release the emergency stop (Class 4)

    xTool says this is the most common cause. Twist the red button to release it. On EU and UK Class 4 machines, press the reset button before the power button.

  2. Check the power adapter

    Seat the power cable and adapter firmly. The adapter's light should stay steady. If it doesn't, try another outlet.

  3. Unplug for 2 minutes

    Disconnect the power cable for about 2 minutes, reconnect, and press the power button.

  4. Check the lens cover

    Make sure the bottom protective cover is off whichever field lens is installed.

If the adapter light won't stay on in any outlet, or it still won't start, contact us. Don't open the machine.

"Access-control key"

The key may not be fully in its port, or may be faulty. Update to the latest firmware and check the key is fully inserted. Still there? Turn the machine off, insert the spare key, and turn it back on.

"Flame detected"

  1. Check for fire

    Look at the machine straight away and put out any flame. Never leave a job unattended.

  2. No fire: cut the reflections

    Reflections off the baseplate can look like flame to the camera. Put the slatted panel under the material, especially when cutting. Repeated high-power passes in one spot can also trigger it.

  3. Metal only: the alarm can go off

    For materials that can't burn, xTool allows turning the flame alarm off in Device settings. Turn it back on before the next job.

"Device moved"

  1. Level it

    A built-in sensor watches for movement. Put the machine on a level, solid surface where it won't be bumped.

  2. Update the firmware

    In xTool Studio, Device settings > Basic info > Check for updates. Use USB and keep the computer awake.

  3. Still happening?

    Take a video and contact us. To keep working meanwhile, xTool allows switching off Stops when moved in Device settings as a temporary measure.

"Exhaust fan installation abnormal"

The machine can't detect the fan module. Power off, take the fan module out and refit it firmly and aligned in its slot, then restart. If the message stays, film yourself reseating it and send it to us with the serial number.

Auto-focus failed or thickness wrong

  • Don't touch the controller buttons while it measures.
  • Put the material under the blue focus spot.
  • Clear, shiny, fluffy or very dark materials won't auto-focus. Lay a thin opaque sheet on top, or focus by hand until the red and blue spots overlap.
  • Use USB if Wi-Fi is slow; the camera images have to reach the software.
  • If the reading with an empty baseplate is far off, or jobs land in the wrong place, run xTool's UV and blue-light laser calibration (video above). Use the test card that is blank on both sides, not the calibration card with black dots.

Before you contact us

Note the exact message, firmware version (Device settings > Basic info) and serial number, and take a short video. Text it to (562) 609-4996.

Watch xTool's video: F2 Ultra UV UV and blue-light laser calibration

More videos

xTool F2 Ultra UV unboxing and first use
xTool F2 Ultra UV: field lens replacement

Embedded from the manufacturer's official channel.

Common questions

My F2 Ultra UV is completely dead, no logo light and no spots. Is the power board gone?

Start with the cheap causes. xTool says a pressed-in emergency stop is the most common reason on Class 4 machines. Release it, check the adapter light stays on, unplug for about 2 minutes, and try again. Only then contact us.

Can I turn off the "Device moved" alarm?

xTool allows turning off "Stops when moved" in Device settings as a temporary measure while you work with support. Level the machine and update firmware first.

Can I turn off the flame alarm?

Only for materials that can't burn, such as metal, and xTool says to turn it back on before the next job.

My cuts have sloped edges near the sides. Is that a fault?

No. xTool says it's normal for galvo lasers: the beam comes in at more of an angle toward the edge of the area. Cut small parts, and place them directly under the laser module.

Engraving on wood is faint or missing. What now?

Restart the machine and make sure the red and blue spots overlap on the surface. If it's still faint, xTool asks for a video of a test engraving on its 3 mm basswood. Send it to us and we'll take it from there.

It's glass that won't mark. Is this the right guide?

Glass has its own causes. See our guide on the F2 Ultra UV not engraving glass.

Did this fix it?