Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool F2 Ultra UV inner engraving: 3D designs inside K9 crystal, setup and fixes for no mark, blur or cracks
Fit the inner engraving lens, install the riser, choose Inner Engraving mode in xTool Studio, and enter the exact measured size and position of a K9 crystal block. Pick the "K9, Inner Carved Glass" material so xTool's parameters load, then preview and start. If nothing appears, check the glass type, mode and dimensions first, then run the Z-axis calibration.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| No mark inside the glass | Wrong glass, wrong mode, sizes don't match, Z focus off | Steps 1 to 4, then Z-axis calibration |
| Blurry or unclear pattern | Layer height or point spacing too large | Fixing results |
| Some areas faint | Not enough energy | Fixing results |
| Flicker or cracks | Too much power or too slow | Fixing results |
| Design too high, too low or shifted | Size or position values wrong, calibration | Steps 4 and 5, calibrations |
| Breaks between layers | Enclosure opened during the job | Fixing results |
Before you start
- Use the right glass. xTool recommends K9 optical crystal. Tempered glass can shatter, laminated glass can delaminate, and deeply tinted glass absorbs the beam, so none of them are good candidates.
- Check the size. The inner engraving area is 70 x 70 mm, and the piece can be up to 150 mm tall. The glass can be a little wider than 70 mm, but the design must stay inside the central 70 x 70 mm.
- Measure every piece. xTool says glass blocks commonly vary by about 2 mm, so measure length, width and height with calipers instead of trusting the label.
- Keep it clean. Dust, oil, fingerprints or liquid on the surface scatter the beam. Handle the glass by the edges.
Step by step
-
Fit the inner engraving lens
Swap the field lens to the inner engraving lens and select it in the software. Our first setup guide for the F2 Ultra UV and xTool's lens video cover the swap. Surface jobs, the rotary and the conveyor all need the surface lens back on afterward.
-
Connect and pick the mode
Connect the laser to the computer with the USB cable and open xTool Studio. Click the processing mode name on the right side and choose Inner Engraving. This switches the canvas to 3D mode.
-
Install the riser
Install the riser platform, secure it, and click Next.
-
Enter the material and its size
Pick the material and type in its length (X), width (Y) and height (Z), or diameter. These numbers must match the real piece. A wrong height is the most common reason a design lands too high, too low, or not at all. Leave the refractive index at the default for xTool's own K9 glass.
-
Position the glass
Either use the positioning piece and enter the values marked on its clips, or enter the bottom-left corner coordinates of the glass on the riser. Then click Import Canvas so the material frame appears on the canvas.
-
Bring in a 3D model
xTool Studio takes STL, OBJ, AMF, 3MF, GLB and PLY files. Keep files under about 100 MB so they load quickly. Use the import icon on the left or drag the file onto the canvas. To turn a flat photo into a relief, use Edit > Adjustments > 3D Photos, click Generate, then Apply.
-
Choose the K9 preset
Click Unknown material in the top-right corner and choose K9, Inner Carved Glass. xTool's recommended parameters load automatically. Resize the model and drag it into place inside the material frame, then check the settings for the object in the right-hand panel.
-
Preview and run
Click Process, then Preview to check the design. Close the enclosure, click Start, wait for Ready, and press the XTOOL Start/Stop button on the touchscreen controller. Avoid opening the enclosure while the job runs.
Fixing results
- Unclear pattern: lower the layer height or the point spacing.
- Some areas faint: raise the power or lower the speed for the whole pattern.
- Flicker or cracks: lower the power, raise the speed, or increase the point spacing. Too much power, or too slow a speed, lets the fractures grow.
- Weak contrast: choose models with strong texture contrast and avoid designs with a lot of black.
- Shifted forward, back, left or right: confirm the value marked by the triangle on the riser top plate matches the Inner Engraving Settings page, or that the bottom-left corner coordinates match where the glass really sits. If they match, run the work area calibration.
- Too high or too low: confirm the height you entered matches the glass, then run the Z-axis calibration.
- Breaks between layers: open and close the enclosure as little as possible during a job, and keep the bench stable. Vibration shows up as layer breaks.
The two inner engraving calibrations
Work area calibration is for engravings that land noticeably away from where you placed them, or come out distorted, even though the glass and parameters are right. It uses the calibration card (the one with black dots, stored in the inner engraving kit) and a blank test card. Z-axis calibration is for designs that come out at the wrong depth. xTool notes that long-distance shipping can shift the internal laser parts slightly, so it is worth checking on a machine that has just been moved. Run the work area calibration again after any Z-axis calibration.
xTool publishes both calibrations as videos only; they are linked on this page. If you would rather not run them yourself, text us at (562) 609-4996 and we will walk you through it.
Glass that isn't xTool K9
Other glass may need its own refractive index. xTool's method: set a reference index, engrave a model of known height, measure the height it actually came out, and multiply the index you set by (model height divided by engraved height). For hearts, stars and other odd shapes, frame the piece with a fixture or blocks so it sits flat, enter the size of that rectangle, and keep the design 1 to 2 mm inside it.
Watch xTool's lesson: inner engraving cubic crystal on the F2 Ultra UV
More videos
Embedded from the manufacturer's official channel.
Common questions
What glass can I inner engrave?
xTool recommends K9 optical crystal. Tempered, laminated and deeply tinted glass are not suitable: tempered glass can break, laminated glass can delaminate, and tinted glass absorbs the beam.
How big can the design be?
The inner engraving area is 70 x 70 mm and the material can be up to 150 mm tall. Keep the design inside the central 70 x 70 mm.
What file types can I use?
xTool Studio accepts STL, OBJ, AMF, 3MF, GLB and PLY 3D files. You can also turn a 2D photo into a relief with the 3D Photos tool.
Why did my crystal crack?
Too much power or too slow a speed. Lower the power, raise the speed, or increase the point spacing.
Can I use the rotary or the conveyor with the inner engraving lens on?
No. xTool says the rotary and conveyor only work with the surface engraving lens fitted.
- Start Inner Engraving with xTool F2 Ultra UV
- A Guide to Glass for Inner Engraving
- Approaches to Improving Inner Engraving Results
- Troubleshoot Inner Engraving Failure in Glass
- Inner Engraving Work Area Calibration for xTool F2 Ultra UV
- Start Z-axis Calibration for Inner Engraving with xTool F2 Ultra UV
- AA support requests about the F2 Ultra UV, 2024 to 2026










































































