Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool F2 Ultra UV first setup: connecting xTool Studio, first job and swapping the field lens
Remove the field lens protector, connect the controller (notch up), power and exhaust pipe, and on the Class 4 model insert the key and release the emergency stop. Connect xTool Studio over USB first, update the firmware, then add Wi-Fi. Use the surface engraving lens for normal jobs and the inner engraving lens only for engraving inside glass. Always power off and unplug before swapping lenses, and never touch the two galvanometer mirrors above the lens.
Set it up
-
Remove the field lens protector
Take it off before every job. Refit it only when the machine will sit unused for a long time.
-
Connect the controller, power and pipe
Plug in the touchscreen controller with the notched side facing up, connect power, and fit the exhaust pipe so it runs outdoors or to an air purifier.
-
Class 4 model only: key and emergency stop
Insert the key, and twist the emergency stop to release it if it is pressed in. Never use the emergency stop as a power switch; xTool warns it can cause damage.
-
Power on and set the language
Press the power button and choose your language on the touchscreen. The logo light is solid when on, blinks slowly while processing, and blinks fast while setting up the network or updating firmware.
Connect xTool Studio
-
Install the software
Download xTool Studio from xtool.com/pages/software. xTool's minimum is an Intel Core i5-6200U, 8 GB RAM and 8 GB free disk on 64-bit Windows 10 or recent macOS.
-
Connect over USB first
Plug in the USB cable (it has both Type-A and Type-C ends), power on, click + New project, then the device icon on the right, + Add Device, and your machine's name.
-
Update the firmware
Open Device settings and click Check for updates under Firmware version. Stay on USB, keep the computer awake, and don't power off during the update.
-
Add Wi-Fi
In Device settings > Basic info, click Setting next to Wi-Fi, choose the network, enter the password, and click Connect with Wi-Fi. The computer must be on the same network. If Wi-Fi later can't find the machine, connect by the IP address shown under Wi-Fi setting.
Your first flat job
-
Warm up
Run the machine for a few minutes first (see the FAQ for times by room temperature).
-
Place and focus
Set the material where the blue spot falls. For cutting, use the slatted panel with its gaps at right angles to the exhaust outlet so air can flow. Hold Up/Down until the red and blue spots overlap. To cut through in one pass, xTool sets focus at the middle of the material: for 6 mm stock, focus on a 3 mm piece, then swap in the 6 mm without changing focus.
-
Pick the material and run
Choose Process on flat surface, pick the material and click Apply, then frame, click Process and Start, and press Start/Stop on the controller when Studio shows Ready.
Keep the enclosure closed while it runs, or wear goggles rated for 355 nm.
Swapping the field lens
| Lens | Use it for |
|---|---|
| Surface engraving | Everything on the surface, including glass surfaces, plus conveyor and rotary jobs. Black outer surface. |
| Inner engraving | Engraving inside glass and crystal, up to 70 x 70 mm. Class 4 kit. |
-
Power off and unplug
Always, before the lens comes off.
-
Swap the lens
Follow xTool's field lens replacement video. With the lens off, two galvanometer mirrors sit above the opening.
Never touch the galvanometer mirrors with your fingers. xTool warns that dirty optics cost power and, in bad cases, cause permanent damage. Clean lenses and mirrors only with a lint-free cloth moistened with absolute ethanol, and wipe the mirrors only if they are visibly dirty.
-
Check before you run
If the machine won't turn on after a swap, make sure the bottom protective cover is off the installed lens. If inner engraving lands at the wrong height or position, xTool has owner calibrations for the inner engraving work area and Z-axis (videos above). Text us at (562) 609-4996 if you'd like us to walk you through them.
Watch xTool's video: F2 Ultra UV unboxing and first use
More videos
Embedded from the manufacturer's official channel.
Common questions
What's the difference between the Class 1 and Class 4 models?
The Class 4 model (MXF-K007-002) adds a key, an emergency stop and the inner engraving pack. On it you can be exposed to Class 4 laser light with the enclosure open, and xTool says it is for trained users. The Class 1 model (MXF-K007-001) has no key or e-stop and keeps the enclosure closed in use.
Which software works with the F2 Ultra UV?
xTool Studio on Windows or macOS, and LightBurn version 2.2.0 or later. xTool says no other third-party software is supported.
Can I use the conveyor for inner engraving?
No. Inner engraving needs the inner engraving lens and positions by numbers you enter. The conveyor needs the surface lens and the camera.
Do I need to warm it up?
xTool suggests about 5 minutes at 20 to 30°C, 5 to 20 minutes at 15 to 20°C and about 20 minutes at 10 to 15°C. Don't run it below 10°C or above 30°C.
The lens barrel has scratches from swapping. Is that a problem?
xTool says bumps and scratches on the outside of the barrel are normal with frequent swaps and generally don't affect use. The glass itself must stay clean.
Are safety goggles included?
No. xTool says to buy goggles that cover 355 nm, with an optical density of 5 or higher.
- xTool F2 Ultra UV User Guide
- xTool F2 Ultra UV Unboxing and First Use
- Connect xTool F2 Ultra UV to xTool Studio on the Computer
- Upgrade the Firmware for xTool F2 Ultra UV
- Process on Flat Surface with xTool F2 Ultra UV
- Replace the Field Lens for xTool F2 Ultra UV
- Troubleshoot Surface Engraving Failure on Glass
- Troubleshoot xTool F2 Ultra UV Not Turning On
- FAQs on xTool F2 Ultra UV
- Routine Care and Cleaning Tips for xTool F2 Ultra UV











































































