Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool F2 Ultra UV with the RA3 or RA2 Pro rotary: levels, marks, focusing and engraving cups and glass
Fit the surface engraving lens first, because the F2 Ultra UV can't run a rotary with the inner engraving lens. Plug the rotary into an extension port, set it on the baseplate marks that match its level (they differ between RA3 and RA2 Pro), and choose a rotary mode in xTool Studio, switching to "RA3 Manual Mode" for an RA3. Put masking tape on the top of glass or shiny metal so auto-measure works, keep the design below the green line, and wear 355 nm goggles.
Which mode and level?
| Setup | Material diameter | Marks to use |
|---|---|---|
| RA3 roller, Level S | 5 to 45 mm | Group 1 |
| RA3 roller, Level M | 40 to 70 mm | Group 3 |
| RA3 roller, Level L | 60 to 100 mm | Group 2 |
| RA3 jaw chuck | Held in the jaws | Group 2 |
| RA2 Pro roller, Level A | 3 to 50 mm | Group 1 |
| RA2 Pro roller, Level B | 45 to 60 mm | Group 2 |
| RA2 Pro roller, Level C | Over 60 mm | Group 3 |
| RA2 Pro chuck | Held in the jaws | Group 3 (Group 4 with the L-shaped module) |
On the RA3, the roller levels are set by which shafts the rollers sit on: S uses shafts A and B, M uses B and C, L uses A and C. The jaw chuck takes the cylindrical jaws alone or with the T-shaped jaws. The two rotaries use different mark groups, so always check the table for the one you have.
The enclosure may not close fully with a rotary in place. Wear goggles rated for 355 nm (plus or minus 5 nm) for every rotary job. They are not included with the laser or the rotary.
Step by step
-
Fit the surface engraving lens
If the inner engraving lens is in, swap it for the surface engraving lens. xTool says the F2 Ultra UV cannot run a rotary job with the inner engraving lens fitted.
-
Connect and place the rotary
Plug the rotary into any extension port with its connection cable. Lift the enclosure, set the rotary on the baseplate, and line up its front bottom edge with the marks for your mode and level.
-
Connect xTool Studio
Connect the laser to the computer by USB and power it on. In xTool Studio click + New project, then the device icon at the top right, + Add Device, and your machine's name.
-
Load the piece
Lay it across the rollers, or clamp it in the jaws. On glass, acrylic, or shiny metal such as stainless steel, put a strip of masking tape on the highest point of the piece, where the beam lands. Without it, focusing and distance measuring fail on these materials.
-
Pick the rotary mode
Click the processing mode name at the top right and choose Roller - Use rotary attachment or Chuck - Use rotary attachment. With an RA3, switch the rotary setting to RA3 Manual Mode. Enter the Diameter or Perimeter of the piece, then click Unknown Material, choose your material and click Apply. If your material isn't listed, leave it as unknown and set the parameters yourself.
-
Focus and set the start line
Check that the red and blue dots both sit on the very top of the piece; if not, move the rotary back onto the right marks. With an RA3, pull the enclosure down as low as it goes. Click Auto-measure: the dots should end up overlapping. Click Refresh background, then drag the green line so it crosses the middle of the piece and the dots. Processing starts at the green line.
-
Lay out and set parameters
Put your design below the green line; the gray area above it is not processed. Set parameters for every object, or the ones you miss may not run. xTool's F2 Ultra UV test matrix article is the place to start for settings.
-
Frame, preview and run
Use the settings icon next to the framing button to set up framing, then click framing to trace the area (click again to stop). In the path settings choose Auto planning or User defining, and turn on Evade smoke when scoring wood or corrugated paper. Click Process, check the notes on the right and Preview Processing Path, put on your goggles, click Start, and press the XTOOL Start/Stop button on the touchscreen controller when the software shows Ready.
Common problems
- Auto-measure fails on glass or a stainless tumbler: add masking tape at the top of the piece where the beam lands.
- Rotary job won't start or the dots are wrong: check the surface lens is fitted and the rotary is on the right marks for its level.
- Part of the design missing: it was above the green line or had no parameters.
Still stuck? Text us a short video of the setup at (562) 609-4996.
Watch xTool's lesson: engraving a cup with the RA3 on the F2 Ultra UV
More videos
Embedded from the manufacturer's official channel.
Common questions
Which rotaries work with the F2 Ultra UV?
xTool lists the RA3, RA2 Pro and RA2. None is included with the laser.
Why does auto-measure fail on my glass or stainless tumbler?
Clear and reflective surfaces confuse the distance measurement. xTool says to put masking tape on the highest point of the piece, where the beam lands.
What level do I set the RA3 to?
Level S for 5 to 45 mm, Level M for 40 to 70 mm, and Level L for 60 to 100 mm diameters.
Do I need goggles?
Yes. The enclosure may not close fully with a rotary, so wear goggles rated for 355 nm (plus or minus 5 nm).
Can I use the rotary with the inner engraving lens?
No. Swap back to the surface engraving lens first.










































































