Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool F2 Ultra UV routine care: monthly 30-minute run, lens and mirror cleaning, fan module and storage
At least once a month, switch the F2 Ultra UV on and let it run for at least 30 minutes so its own heat dries out moisture, and check that the field lens and galvanometer mirrors are clean. Clean optics only with a lint-free cloth and absolute ethanol, with the power unplugged, and never touch the mirrors. Brush out the fan module when smoke escapes, and never wash it. Run it at 10 to 30°C in a dry room.
Care at a glance
| When | What to do |
|---|---|
| Monthly, at least | Run it 30 minutes or more; check lens and mirrors |
| Before each job | Remove the field lens protector; warm up in a cool room |
| Engraving shallow | Clean the field lens |
| Mirrors visibly dirty | Clean the galvanometer mirrors |
| Smoke escaping | Clean the fan module and fan guard |
| Long breaks | Refit the lens protector; store dry |
Monthly: the 30-minute run
-
Run it for at least half an hour
Power on and leave the machine running for 30 minutes or more. The heat it makes dries out moisture inside and protects the humidity-sensitive UV laser parts. Put it on your calendar if the machine sees light use.
-
Look at the optics
With the power off, check that the field lens and, if you have the lens off, the two galvanometer mirrors are free of dust and debris. Dirt lowers quality and can damage the optics over time.
Clean the field lens
-
Unplug the machine
xTool says to disconnect power before any cleaning or lens swap.
-
Wipe with absolute ethanol
Moisten the lint-free cloth from the box with absolute ethanol and wipe the lens gently. This applies to both the surface engraving lens and the inner engraving lens.
Clean the galvanometer mirrors (only if dirty)
The two mirrors sit above the field lens and are only reachable with the lens removed. Wipe them gently with a lint-free cloth moistened with absolute ethanol, and only when you can see dirt.
Never touch the galvanometer mirrors with your fingers. xTool warns that letting the optics get dirty causes power loss and poor results, and in bad cases permanent damage. If a mirror looks scratched or stained after cleaning, stop and contact us.
Clean the fan module
-
Remove the fan guard
With the power off, pull the magnetic fan guard off the smoke outlet.
-
Take out the fan module
Open the cover and lift the fan module out, then open its cover to reach the fan.
-
Brush it clean
Brush dust off the fan module and the guard, then refit both firmly in their slot.
Never rinse or soak the fan module in water. It holds electronics. If you see "Exhaust fan installation abnormal" after refitting, power off and reseat the module until it sits firmly and aligned, then restart.
Where and how to keep it
- Work at 10 to 30°C (50 to 86°F) in a dry, well-ventilated room. Don't run it outside that range.
- In a cool room, warm it up before jobs: about 5 minutes at 20 to 30°C, 5 to 20 minutes at 15 to 20°C, and about 20 minutes at 10 to 15°C.
- Use the slatted panel for thin or clear materials so the laser doesn't mark the baseplate, which is not removable. Lay the slats with the gaps at right angles to the exhaust outlet.
- For long breaks, refit the field lens protector and store the machine somewhere dry. Keep up the monthly run if you can.
Watch xTool's video: removing and replacing the F2 Ultra UV field lens
More videos
Embedded from the manufacturer's official channel.
Common questions
Why does a UV laser need running when I'm not using it?
xTool says the UV laser's core parts are sensitive to humidity. Left unused for a long time, for example over six months, especially in a humid room, parts such as the frequency-doubling crystal can age faster and lose performance permanently. Running it monthly dries it out.
Can I use isopropyl alcohol on the lens?
xTool specifies absolute ethanol for the F2 Ultra UV's field lens and galvanometer mirrors. Use that.
The laser module fans keep spinning when it's idle. Is that a fault?
No. xTool says that is normal in standby. After 30 minutes idle (the default) the laser module sleeps, and the fans stop once it cools down.
How long can I run it in one go?
In the right temperature and humidity it runs continuously, but xTool recommends no more than 8 hours at a time to get the most life from the laser.
What are the storage conditions?
xTool lists -10 to 60°C and 10 to 60% relative humidity for storage, and 10 to 30°C with 10 to 60% humidity while working. Store it dry, with the field lens protector fitted.










































































