Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool laser not connecting to xTool Studio: "Device not found" over USB or Wi-Fi
Update xTool Studio first, then run its built-in Connection detection, which tells you whether the cable, driver, firewall or network is the problem. Use the original USB cable straight into the computer, quit any VPN, and on a Mac allow xTool Studio under Local Network. For Wi-Fi, the laser and computer must be on the same network, and the network name and password must avoid special characters.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| "Device not found" over USB, first time | Old software, wrong port, cable, driver, firewall or VPN | Steps 1 to 6 |
| "Connection failed" on a machine that used to connect | Software or OS update, glitch, VPN, cable | Steps 1, 2 and 5 |
| Your network is not in the Wi-Fi list | Hidden network, weak signal, special characters | Step 7 |
| Network shows but setup fails | Different network, password, proxy | Step 7 |
| Set up on Wi-Fi before, now missing | Discovery blocked on the network | Step 8 |
Step by step
-
Update the software and restart
Install the latest xTool Studio. The P3 does not work with XCS at all, and older XCS versions may not recognize the F2 Ultra. Then turn the laser off and on and replug the cable. On the F2 Ultra, confirm it is really on: the logo light is lit and the red and blue dots show on the baseplate.
-
Run Connection detection
With USB connected, go to the gear icon, Device > Connection detection > Start, and click Allow on any permission pop-ups. The result tells you which of the next steps to focus on.
-
Check the cable and port
Use the original cable, straight into the computer. On a desktop, use a port on the back. On the P3, make sure you are in the USB connection port, not the access-control key port. Look at both cable ends for damage and try another port or computer. If you replace the cable, xTool suggests a USB 3.0 data cable no longer than 2 meters.
-
Install the driver
Go to Settings > Device and click Install driver if it is not installed. On the F2 Ultra this is the RNDIS driver.
-
Turn off VPNs, proxies and firewalls for a test
Quit VPN software and turn off any system proxy. On Windows that is Settings > Network & internet > Proxy; on a Mac, System Settings > Network > Wi-Fi > Details > Proxies. Temporarily turn off the firewall and any antivirus with a network firewall, then try again. Turn them back on afterward and add an exception for xTool Studio.
-
Mac only: allow local network access
Go to System Settings > Privacy & Security > Local Network and turn on xTool Studio. If it is already on, quit xTool Studio, toggle it off and on, and reopen. On a laptop, plug in the charger and turn off Low Power Mode.
-
Fix Wi-Fi setup
Set up Wi-Fi while connected by USB. Put the computer on the exact same network as the laser. If the network is hidden, make it visible in your router. Remove special characters such as ' " ! or \ from the network name, and keep the password at 32 characters or fewer. A quick test is a 2.4 GHz phone hotspot: if the laser connects to that, the issue is your router's settings.
-
Connect by IP
With USB connected, copy the IP address from Device settings > Basic info > Wi-Fi setting. Then open Connect device > IP, paste it and click Connect.
xTool's own steps for the P3 go as far as opening side panels and reseating internal cables. Do not open the machine yourself. If you reach that point, contact us first.
Still not connecting?
Export the work log from Device settings > Basic info if you can, note your serial number, take a short video of the error, and text it to us at (562) 609-4996.
Common questions
It worked yesterday and now says "Connection failed". What changed?
Often a software, firmware or OS update, a VPN or a firewall. Restart the laser, replug the cable and update xTool Studio before anything else.
Can I use a USB hub?
Avoid it if you can. If you must, make sure the hub port carries data, not just power, and do not hang other devices off it.
My Wi-Fi password is long. Is that a problem?
It can be. xTool says passwords over 32 characters, and names or passwords with characters like ' " ! or \ can make setup fail.
The laser was on Wi-Fi but disappeared from the list.
Connect by IP address. Find it under Device settings > Basic info > Wi-Fi setting while connected by USB, then use Connect device > IP.
I am using XCS on a P3.
That will not work. The P3 only connects to xTool Studio.
- Troubleshooting: USB Connection Issues with xTool P3
- Troubleshooting: Wi-Fi Connection Issues with xTool P3
- xTool Studio Can't Find xTool F2 Ultra Through USB
- XCS Can't Find xTool F2 Ultra Through Wi-Fi
- AA support requests about xTool connection problems, 2024 to 2026











































































