Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool laser safety basics: fire, fumes, goggles and what never to laser
Never leave a running laser unattended, keep a CO2 extinguisher within reach, vent fumes outdoors or through a purifier, and never laser PVC or vinyl. The P3 is an enclosed Class 1 machine with lid interlocks. The F2 Ultra is a Class 4 laser: xTool requires goggles rated for 445 nm and 1064 nm and the enclosure closed with Stops when enclosure opened turned on.
This is a summary. Read the Safety First guide for your exact model before the first job: links are on each machine's page.
Know your laser class
| Machine | Class | What it means |
|---|---|---|
| P3 | Class 1 machine with a Class 4 laser inside | The beam stays enclosed. Interlocks on the lid and baseplate stop the laser. Never run it with the lid up or parts removed, and keep magnets away from the interlock switches. |
| F2 Ultra | Class 4 | For trained users only. Wear goggles rated for 445 nm and 1064 nm. Keep the enclosure closed with Stops when enclosure opened on. If a part is too big to close the lid, xTool requires a controlled laser area set up by a Laser Safety Officer. |
Fire
- Never leave the laser running unattended. Setting mistakes or a fault can start a fire.
- Keep a CO2 extinguisher within reach and make sure everyone knows how to use it.
- Cutting at low speed and high power is the most likely way to get open flame. Acrylic is especially flammable when vector cut.
- If flame appears, press the emergency stop, step back, and use the extinguisher.
- After every job, open the lid, remove the work, check for embers, and clean out scraps and residue.
- Keep paper, solvents, alcohol and other flammables away from the machine.
Fumes
- Run the exhaust pipe outdoors or into an air purifier, and check and change purifier filters on schedule.
- Never process PVC, vinyl, or anything containing chlorine. xTool also warns about ABS, polycarbonate and materials containing benzene, ammonia, fluorine, phenol or aldehydes.
- Never laser a material you cannot identify.
- If you smell strong fumes or feel dizzy or short of breath, stop, leave the room, and do not return until the air clears.
Electrical and setup
- Set the laser on a stable, flat, non-flammable surface, away from children.
- Never open access panels while the machine is plugged in, and unplug before any maintenance.
- Do not use the emergency stop as an on/off switch. xTool warns it can damage the machine.
- Check the machine for damage before each use, and do not run it if anything is broken.
- Metal parts stay hot after engraving on the F2 Ultra. Let them cool or use heat-resistant gloves.
Room conditions
xTool rates the F2 Ultra for 15 to 30°C and the P3 for 5 to 30°C at 30 to 60% humidity. Never run either below 0°C.
xTool lasers are not user-serviceable inside. If something is damaged or behaving strangely, stop and contact us at (562) 609-4996.
Watch xTool's video: How to use the xTool Fire Safety Set
More videos
Embedded from the manufacturer's official channel.
Common questions
Do I need goggles with an enclosed laser?
It depends on the class. xTool requires goggles rated for 445 nm and 1064 nm on the Class 4 F2 Ultra. Class 1 machines like the P3 contain the beam when the lid is closed, but never defeat the lid interlocks.
What fire extinguisher should I keep?
xTool recommends a CO2 extinguisher kept on hand, with everyone in the shop trained to use it. xTool also sells a Fire Safety Set for its P and F series.
Can I engrave my HTV or sign vinyl?
No. Vinyl and PVC release corrosive, toxic fumes that harm people and damage the laser.
Can I run the exhaust into the room if I open a window?
xTool's F2 Ultra guide says the exhaust must go outdoors or to a qualified air purifier, never directly into the room.
- xTool F2 Ultra Safety First
- xTool P3 Safety First
- 10 Tips to Ensure a Safe and Clean Lasering Experience
- AA support requests about xTool lasers, 2024 to 2026











































































