Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool P3 "No material detected" or auto-measure failed: how to fix it
In auto mode the P3 finds your material with its camera and focuses by bouncing a laser dot off it, so detection fails when the material is too small, near the edge, transparent, shiny, matte black, or when the measuring point lands on a hole or a covered slat slot. Center the material, keep the origin and slat slots clear, cover clear or shiny material with white masking tape, and keep strong light off the lid. If it still fails, switch to manual mode and focus manually.
How auto mode finds your material
In auto mode the P3 photographs the bed with its camera to find the material, then measures distance by bouncing the laser dot off it and sets focus from that reading. It measures from the slat slots, which act as its reference points, with the lifting platform at 30 mm. It only handles flat material at one height. Detection fails when either the camera or the distance sensor cannot get a clean reading.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Material not detected at all | Too small, too near the edge, too transparent | Steps 1 and 2 |
| Detected with the lid open, fails after closing | Measuring point blocked, platform height, light, panel | Steps 3 to 6 |
| Fails on clear, shiny or matte black material | Sensor cannot read reflected light | Step 2 |
| "Concentric circles not detected" | Dirty or covered circle stickers, lid closed slowly | Step 7 |
| Fails only on the conveyor feeder | Material not covering both sensors | Step 8 |
Step by step
-
Center the material
Small pieces and pieces near the edge often fail because the camera cannot see the whole outline. Move the material to the middle of the bed and detect again. For a small piece, click it on the canvas to start measuring.
-
Cover clear, shiny or black material
Distance measurement depends on light bouncing back. Clear acrylic, glass, mirrors, very reflective material and matte black or dark fabric can all fail. Put white masking tape on the material where it will be measured, or switch to manual mode. If something sits under clear material, the P3 may focus on that instead, which can drive the air nozzle into your work.
-
Keep the origin and slat slots clear
Material on the origin or on the right-side slat slots blocks the reference point. In auto mode, scraps and residue on the bed can be mistaken for material and push the reading out of range, so clean the bed.
-
Check the platform height
Turn the lifting platform knob to raise the platform to 30 mm. The material surface must be at least 4 mm below the air nozzle. For thicker material that needs a lower platform, use manual mode, which goes to 220 mm.
-
Check light and the panel
Bright light shining through the lid can upset the measurement, so keep the machine out of direct sun and strong lamps. Use xTool's black honeycomb panel or slats; xTool says third-party panels with silver grids can interfere.
-
Check where it measures
The P3 picks the measuring point itself. On a part with cutouts it can land in a hole. If it does, exit auto mode and measure manually on a solid area. Then clean the distance sensor: put a mirror under the laser module to look at it, and if it is dirty wipe it gently with a lint-free cloth moistened with alcohol.
-
Fix the camera reference
For "Concentric circles not detected", make sure the circle stickers in the corners are clean and uncovered and that thick material is not near them. Close the lid in one smooth, fairly quick motion; a slow or hovering close triggers another photo that can fail. Do not slam it either, as hard knocks upset the lid angle sensor. If the camera view in the processing monitor is blurry, clean the camera lens.
-
Conveyor feeder only
The material must cover both the sensor at the front of the P3 and the sensor on the feeder. Cover holes over either sensor with masking tape on the back, and tape the back of black matte, clear or mirror-like material.
Focus manually instead
Turn off auto mode. Measure from the bottom of the laser module's front cover down to the material surface, subtract 30.5 mm, and enter that number. With the conveyor feeder, enter the measured material thickness. Keep at least 4 mm between the material and the nozzle.
If the sensor's red dot is missing, dim or lands outside the slats, xTool's fix involves removing the laser module cover and reseating or calibrating the sensor. Do not open it yourself; contact us first.
Still failing?
Update xTool Studio and the firmware, then export the work log, note your serial number, take a short video of the error and text it to us at (562) 609-4996.
Common questions
It detects the material with the lid open, then fails after I close it. Why?
That is when the P3 measures distance. Check that the material is not on the origin or covering the right-side slat slots, that the platform is at its 30 mm auto mode height, and that bright light is not shining through the lid.
Can the P3 auto-measure clear acrylic or glass?
No. xTool says transparent and mirror materials are not supported. Cover the measuring spot with white masking tape, or use manual focus.
Does it matter which honeycomb panel I use?
Yes. xTool says its black honeycomb panel and slats measure reliably, while third-party panels with silver grids can interfere.
What is "Concentric circles not detected"?
The P3 uses circle stickers in the corners to orient its camera. Keep them clean and uncovered, keep material away from them, and close the lid in one smooth motion.
How do I focus manually?
Measure from the bottom of the laser module's front cover to the material, subtract 30.5 mm, and enter the result. With the conveyor feeder, enter the material thickness instead.
- xTool P3 Auto Mode FAQs
- Solutions for Auto-Measure Failure
- P3 Automation Overview and Precautions for Use
- Concentric Circles are Not Detected
- xTool P3 Fails to Detect Materials in Use Conveyor Feeder Mode
- How to Perform Manual Focusing for xTool P3
- AA support requests about xTool P3 material detection, 2024 to 2026










































































