Support
Machine type
Brand
Epson SureColor F2100

Epson F2100 long-term storage: when and how to use Storage Mode

✓ Reviewed by Jason KimUpdated 2 min readFits: F2100 · F2000
Short answer

If your F2100 will sit with the power off for a month or more, Epson says you must put it in Storage Mode, which swaps the ink for cleaning cartridges. Skip it and the head may clog so badly it can't be cleared. For shorter breaks, print a nozzle check at least once a week, and if it will sit more than two weeks you can swap only the white for cleaning cartridges with Replace White Ink.

Match your situation

How long it will sit What Epson says to do
Overnight or a weekend Turn it off normally at the end of the day. Shake the whites and print a nozzle check when you come back.
Up to two weeks Print a nozzle check at least once a week while you're away.
More than two weeks, less than a month Keep printing a weekly nozzle check, or swap the white for cleaning cartridges with Maintenance > Replace White Ink.
A month or more, power off Run Storage Mode (steps below). This is required, not optional.

Before you start

Storage Mode takes about 45 minutes. Gather:

  • Cleaning cartridges. Epson's maintenance schedule lists six 700 ml cartridges. You may need new ones depending on how much fluid is left in any you already have.
  • Two waste ink bottles, or at least enough free space, because the printer asks you to replace the bottle at the end.
  • The maintenance kit (gloves, cleaning solution, cup, swabs) and the plastic tweezers.

Step by step

  1. Clean the suction cap first

    Epson's schedule says to clean the cap before Storage Mode. Choose Maintenance > Head Cap Cleaning, clean the cap with a swab dampened with ink cleaning solution, close the cover and press OK. Our clogged nozzle guide walks through the cap cleaning in detail.

  2. Start Storage Mode

    Turn the printer on. Press the maintenance button, highlight Storage Mode, press the right arrow, highlight Yes and press OK.

  3. Swap the ink for cleaning cartridges

    Follow the screen. Pull each ink cartridge straight out by the indentation on top and slide a cleaning cartridge into its slot, label side facing the side of the printer. Don't touch the chip on the cartridge. You don't need to shake cleaning cartridges.

  4. Replace the waste ink bottle

    When the cartridges are done, the screen tells you to replace the waste ink bottle. Wear gloves, move the tube to the new bottle, cap the old one with the caps from the new one, and press OK to reset the counter. Dispose of the waste ink according to your local rules.

  5. Turn it off and store it properly

    Turn the printer off with the power button. Leave the waste ink bottle installed, because ink left in the tubes can still drip. Make sure the head is parked and capped on the right side before you walk away, close every cover, and drape an anti-static cloth or cover over it. Keep the room within Epson's storage range of -4 to 104°F.

Don't leave any cartridge slot empty, even in storage. Epson warns the ink in the printer can dry out.

Bringing it back

  1. Install the ink

    Turn the printer on and follow the screen to put the ink cartridges back. Shake each one for about 15 seconds first. Flip the white ones over and shake again.

  2. Check and clean

    Print a nozzle check before you print anything. If channels are missing, clean the suction cap, then run head cleaning, starting at Light on just the channels with gaps.

If the white still won't come back after a cap cleaning and a few cleanings, text us a photo of the nozzle check at (562) 609-4996.

Watch Epson's video: cleaning the F2100 suction cap before storage

Embedded from the manufacturer's official channel.

Common questions

How many cleaning cartridges do I need for Storage Mode?

Epson's F2100 maintenance schedule lists six 700 ml cleaning cartridges. Partly used ones count if they still have enough fluid in them, but have spares on hand, because the printer tells you to swap any that run short.

Can I just unplug the printer while I'm away?

No. Epson warns that cutting power at a power strip or breaker while the printer is on can leave the head uncapped, and that storing it a month or more without Storage Mode can leave clogs that can't be cleared.

I'm closed for two weeks. Do I need Storage Mode?

No. Print a nozzle check at least once a week, or replace the white with cleaning cartridges (Maintenance > Replace White Ink). On the older F2000, Epson says to replace the white once you'll be idle two weeks or more.

What do I do with the ink cartridges I took out?

Wipe the ink supply port with a cleaning stick from the maintenance kit, keep the port free of dust, and don't tape over it. Store them flat at room temperature out of direct sunlight. Epson says to use ink within one year of first installing it.

The nozzle check is bad after storage. What now?

That's common after a long idle. Clean the suction cap first, then clean the print head, the same order Epson gives for any printer that hasn't been used in a while.

Did this fix it?